12:4
Use and safety instructions
Instructions and directions
Elpress hydraulic and mechanical tool
systems are some the safest the
market.
Correct use the tools:
• increases productivity
• increases tool life
• ensures the quality work done
• minimises the risk accidents
Safety rules
Below are some simple and common
rules that Elpress recommend all
operators follow:
• Before starting work with crimp tool,
a thorough visual inspection should be
carried out.
• Measure with calipers and compare
with the table’s ”N”dimensions. max mm
16 6. This
shape change provides both mechanical
strength and good electrical properties.
• Pay attention the risk crushing
and cutting injuries during work. Each Elpress tool therefore
accompanied detailed instructions on
how use the tool.8
50 10.
• All operators must wear personal pro-
tective equipment such A51 gloves,
goggles and safety shoes.
• The tools must serviced and calibra-
ted regular intervals. This
applies all types crimping tools
and cable cutters.
Crimp die table type KRD/KSD
(N-measurement)
Type KRD/KSD
with B-dies
KRD/KSD Die No. These instructions
should read carefully before use, the
best interests the operator.
• Check that the installation unpowered
before carrying out work.2
150 16.0 (KB dies)
120 15. max mm
10 6,3
16 7,3
25 8,8
35 10,2
50 14,5 11,2
70 13,4
95 16,4
95 15.3
35 8.The
hose made for particularly high pressure
and cannot replaced another type.0
120 15.7
240 19. Pump, crimp head, forks,
couplings, hoses and other accessories
must checked ensure that they are
faultless and clean.3
185 17.
• Operate with caution, not drop
heavy objects the hydraulic hose.
• Make sure that the correct tool tool
insert has been selected for the termi-
nal and conductor crimped.5
Crimp die table type KRF/KSF
with Dual dies measurement)
Type KRF/KSF
with DUAL dies
KRF/KSF DB-die max mm
10 6,7
16 7,5
25 9,0
35 10,6
50 14,5 11,8
70 13,6
95 16,0
120 17,7
150 20,3
185 21,7
240 23,9
300 25,7
400 30,5
Crimp die table type KRF/KSF
(N-measurement)
Type KRF/KSF
with B-dies
KRF/KSF Die No.
• there suspicion failure a
crimp system, always contact the
Elpress Service Centre.6
70 13.2
70 11.2
150 16,3
185 20.9
16 8. max mm
10 5.
• Hydraulic pressure must not applied to
a hose that heavily bent knotted.2
35 10.
Check crimping results
In order ensure that the tool has
achieved the predetermined shape
change for each cable terminal, the
crimp result shall measured. this
happens, contact doctor immediately.8 (KB dies)
120 15.2
50 11.
Hexagonal crimping
For terminals and through connectors of
copper the following applies:
• The ”N”dimension checked the
direction the crimp.3
400 24.0
95 13.5 7.0 (KB dies)
120 15.
• Keep mind that there very high
crimp pressure during work.3
25 7.5
300 23.6
95 13.5
300 23.3
400 24. The correct place-
ment the inserts the forks should
also checked before starting work.5
Crimp die table type KRT/KST
(N-measurement)
Type KRT/KST
with B-dies
KRT/KST Die No. leakage
occurs, oil under high pressure may
come into contact and penetrate the
skin resulting internal injury.0
95 14. The tools are
not designed for “Live working”.
• Hydraulic tools must never carried in
the hose coupling. Safety requires that instructions
and directions are available and followed
closely. Therefore,
never stand front tool the
direction crimping force.5
25 8.
This can damage the steel reinforce-
ment and cause leakage.
• the measurement result exceeds
the ”N”dimension (according the table
that follows) after correct contact crim-
ping, contact the Elpress service centre.8 (TB die)
120 16,3
150 20,1
150 20,3 (CB and dies)
185 20,5
240 23,3
300 24,5
400 30,3
500 30,4
630 38,4
800 38,4
.1
185 20,3 (CB and dies)
240 20
