Snímač pohybu, přítomnosti a osvětlení KINASGARD® ABWF ⁄ LF

| Kategorie: Leták / Datasheet  | Tento dokument chci!

Vydal: Domat Control System s.r.o.

Strana 10 z 12







Poznámky redaktora
– warranties liabilities will assumed for defects and damages arising from improper use this device. The output signal tapped measuring instrument.. Take care not damage the cable sensor when opening housing. – Operating this device close other devices that not comply with EMC directives may influence functionality. – necessary for mounting and electric wiring, unplug connector carefully and plug back again the same position afterwards.. avoid damages and errors the device (e. Deviations from the catalogue representation are not explicitly mentioned and are possible terms technical progress and continuous improvement our products. – case complaint, only complete devices returned original packing will accepted.General notes – The sensor mounted inside the housing cover.g. The area around the brightness sensor must not obstructed. – This device must not used for monitoring applications, which serve the purpose protecting persons against hazards injury, or EMERGENCY STOP switch for systems machinery, for any other similar safety-relevant purposes.10V 0V/GND Power supply AC 24V~ 0V DC 15-36V GND Circuitry 0. Therefore, pay attention correct wiring! Circuitry Circuitry 0. All outputs field devices must be referenced the same potential! In case reversed polarity one field device, supply voltage short-­ circuit would caused that device. The brightness sensor positioned the far end the cable gland. – This device shall only used for its intended purpose. – case any modifications made the user, all warranty claims are forfeited.10V 0V/GND 0. Commissioning mandatory and may only performed qualified personnel! These instructions must read before installation and commissioning and all notes provided therein are regarded! Connecting scheme Parallel operation Connecting scheme Individual operation SUPPLY VOLTAGE : For operating voltage reverse polarity protection, one-way rectifier or reverse polarity protection diode integrated this device variant. – Scratches, dirt, and also partial shading falsify the measuring result.10V 0V/GND V Power supply AC 24V~ 0V DC 15-36V GND . – Modifications these records are not permitted.. – Dimensions enclosures housing accessories may show slight tolerances the specifications provided these instructions.36 supply and GND for ground wire! When several devices are supplied one voltage supply, to be ensured that all ”positive“ operating voltage input terminals (+) the field devices are connected with each other and all ”negative“ operating voltage input terminals (–) reference potential) are connected together (in-phase connection field devices). Our “General Terms and Conditions for Business“ together with the “General Conditions for the Supply Products and Services the Electrical and Electronics Industry“ (ZVEI conditions) including supplementary clause “Extended Retention Title“ apply the exclusive terms and conditions. Output ­ voltage measured her against zero potential the input voltage! When this device operated supply voltage, the operating voltage input UB+ used for 15. When operating under deviating conditions, recommend performing an initial manual adjustment on-site during commissioning and subsequently regular intervals. voltage induction) shielded cables are used, laying parallel with current-carrying lines avoided, and EMC directives are observed. radiators) exposed their heat flow. The purchaser has adhere the building and safety regulations and has prevent perils any kind.. – Consequential damages caused fault this device are excluded from warranty liability. Respective safety regulations issued the VDE, the states, their ­ control authorities, the TÜV and the local energy supply company must observed. The consequential short-circuit current flowing through this field device may cause damage it. In addition, the following points are observed: – These instructions must read before installation and putting operation and all notes provided therein are ­ regarded! – Devices must only connected safety extra-low voltage and under dead-voltage condition.. This internal one-way rectifier also allows operating devices AC ­supply voltage.. – These devices must installed and commissioned authorised specialists..g.. Direct sun irradiation heat ­ irradiation similar sources (powerful lamps, halogen spotlights) must absolutely avoided. – this device operated beyond the specified range, all warranty claims are forfeited. – Applying overvoltage will destroy the device. Notes commissioning: This device was calibrated, adjusted and tested under standardised conditions. – Protect sensor surface against any kind dirt and damage. – This device must not installed close heat sources (e. – The technical data and connecting conditions the mounting and operating instructions delivered together with the device are exclusively valid