The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
Poznámky redaktora
1
2
. 100 m
Mounting angle for ceiling Mast fastening
Ceiling mounting angle for
2 Controllers/sensors
Edge mounting device
71,4
100
60
65
21
31,2
30,521,2
10,5
68
2,4 m
50°
Tilt
Curtain effect
1.
.
Cabling
Connection parallel per Figure in
star configuration per Figure Mixed
forms are also permissible.
.
S Switch signal
Lx Brightness signal
Lxo: Unconnected terminal, which
can used loop-through
the signal.
Curtaining effect and range optimization
By tilting the controller downwards its range can steplessly adjusted.
.T26
Lx
2939
S
Lx
2939
S
Connection:
Important!
Each controller system sensor has brightness
sensor, but only one brightness sensor may be
connected within system, i.g.
Crawl-under protection
The controller system sensor 240 has separate
crawl-under protection. When using the controller
system sensor 240, detection can further optimized reducing the
sensitivity. the "Lx" terminal
is assigned only one controller system sensor.
up min.
up min.e. This results an
even higher degree security.
2
Lxo
S
+
-
Lx
+L
N
Lx
-
S
+L
N
Lx
-
S
1 .
A special protective screen front the controller
protects against the effects thermal influence.
1
Lxo
+
-
Lx
Lxo
S
+
-
Lx
x
+L
N
Lx
-
S
1
2
.
During installation
When installing the controller, should ensured
that the lens not exposed direct sunlight
(otherwise the sensor may damaged). setting
up min. increase the
connected load use contact maker.
.
Communication lines are recommended for
connection the controller system
sensors, e. The controller
system power pack thus switches off (even there constant movement the
detection area the controller system sensors), the latest after minutes.
Connecting terminals:
+,- Power supply 15V=.
Installation location
The controller should protected against direct
rainfall, because rain drops the lens may cause
unwanted switching.
Detection then occurs only the close-up range. after dawn) the lighting does not remain switched unnecessarily, the
controller system power pack equipped with limit switch-off.
max. min.
It switches again when the brightness drops below the set response brightness and
there motion the detection area.g.
.5 m
Limit switch-off
If the controller system power pack switched on, the response brightness no
longer evaluated. a
horizontal position the detection beams may point
directly the sun (see illustration). Switch-off
Controller
Installation instructions
.
This enables the functioning checked and the
detection range adjusted without switching the load.
Controller system
The controller system can used wherever multiple controllers are used switch the same load.
Diagnosis LED
To enable the controller system tested accurately,
the controller system sensors are fitted with testing
and diagnosis LED.
Only this controller system sensor measures the
brightness and forwards this value the
controller system power section for evaluation. JY-ST-Y 2x2x0.
. sec.8 4x0. The controller system installed described below.
90 min.
. This LED lights response to
every movement, regardless brightness.
System-Leistungsteil
max. minutes
up min. therefore
advisable keep the sensor head away from sunlight
until mounted the housing body. minutes
up min.
. This means that movements
underneath the controller system sensor are also
detected, right the house wall.
. 100 m
max.
.
total shortening the
on-time delay time
up min.
Recommended responsiveness setting
+- +-
Lxo
S
+
-
Lx
x
Lxo
+
-
Lx
+L
N
Lx
-
S
max. sec.
. 100 m
max.
In figures and the controller system sensor
with the active brightness sensor identified by
an "X". 100 m
1
2
8
.
.
. However, that even when there constant motion the detection
area (e.
The delay time (time which the light still remains switched after more motion is
detected) automatically shortened depending the entire on-time.8
Connection multiple controller system
powerpacks single controller system
sensor cable not permissible,
malfunctions will result.
System-Leistungsteil
max.
.
Accessories
Use the mounting
accessories allows the
controllers fixed at
difficult locations, such as
on ceilings masts, in
corners
