The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
Poznámky redaktora
Press 3x: the Berker control unit switches off for hours, then
brightness-dependent controller operation. The Berker
control unit switches for approx.
Press 4x: test mode: brightness evaluation disabled.
Pressing repeatedly additional functions.
When switching back on, "S1" activates switching
operation the Berker control unit for the pre-set
delay time. after dawn), the unit fitted with limit cut-out. minutes
Up min.
Controller operation (monitoring)/
CONTINUOUSLY ON
The "S" switch allows changeovers between controller
operation and CONTINUOUSLY ON.
(BK) black: (phase)
(BU) blue: (neutral conductor)
(BR) brown: (relay, lamp cable)
Note: When using energy saving lamps, consider high
inrush currents. sec.
Electrical connections
Connections executed plug-in terminals.
L
BK
N
BU
μ
BR
L
N
μ
60
88,3
103
52,7
37,9
T T
N L
L
N
T
N L
L
N
S S
N L
L
N
S
N L
L
N
S
N L
L
N
S1
S2
N L
L
N
S1
S2
N L
L
N
T
N L
L
N
N L
L
N
Auto manual mode with 3-step switch
1 Controller operation
2 All Off
3 CONTINUOUS ONS
N L
L
N
1 3
Berker control
. 0185.
When the Berker control unit switched and
CONTINUOUSLY set, the neon lamp unit lights
up.g. expires only when more movement detected. Set time
Up min.
With push-button (NC)
Existing switches can replaced push-button
"T".g. sec.
Controller operation/CONTINUOUSLY ON
changeover switching
The "S" switch allows changing over between
controller operation and CONTINUOUSLY ON. activates non-brightness-dependent
switching operation for the set delay time. long movement detected Berker control unit,
the lighting remains on. To
prevent the lighting from remaining when there continuous movement the
detection range (e. The
delay time determined the Berker control unit with the longest remaining time.
Connection multiple Berker control
units "with intelligent load linking"
Caution: All parallel connected Berker control
units must run the same phase.
Controller operation/CONTINUOUSLY ON
The "S" switch allows changeovers between controller
operation and CONTINUOUSLY ON.
Additional functions
The Berker control unit permits different operating modes, using push-button (NC)
in the lead cable:
Press 1x: non-brightness-dependent switch-on for the pre-set delay
time, then brightness-dependent controller operation. Pressing the push-button once
for min.
Pressing repeatedly additional functions. The delay time
(time which the light remains after more movement detected) shortened
depending the overall time.
For timer programmed switch-on the Berker control
unit non-brightness-dependent switching operation
is executed for the pre-set delay time. sec.
Auto/manual operation with series switch
S1 open, open: all off. 0123
N L
T
Intelligent
load linking
N L
L
N
L
N
N L
L
N
N L
L
N
T
N L
L
N
Switch-on timer
Timer programmed activation and shutdown the
Berker control unit. cut-out
The Berker control unit thus cuts out after minutes the latest, even there is
continuous movement the detection field.T24
Changeover switching
Existing changeover switches can replaced by
push-button "T" (NO). This
makes possible construct controller system comprising units with equal rights,
with mutual interference.
Parallel connection does not increase the
max. necessary use inrush current limiter
order no. seconds when a
movement detected.
The built-in microprocessor conjunction with
a voltmeter the load cable means that all
parallel connected Berker control units detect
the switching light. min.
activates non-brightness-dependent switching
operation for the pre-set delay time.
Suppressor
Order no.
Limit cut-out
Once the Berker control unit has switched on, the brightness longer evaluated.
Up min.
Switch off
Using "S1" "S2" switch.
Before installing the terminating outlet, open the
two condensate drains the bottom (do not this if
installing dusty rooms). for flash circuit).
S1 closed, closed: CONTINUOUSLY ON
S1 closed open: controller operation
Switch-on timer
Timer programmed switch-on the controller. sec. Pressing the push-button once for min.
With push-button (NO)
Pressing push-button "T" (NO) once for min. "S2" does not this, only the load is
switched off. The delay time restarted every time movement detected in
the relevant Berker control unit.
Operation timer flash relay
Extension delay time operation clock relay
(e.
Press 2x: the Berker control unit switches for hours, then
brightness-dependent controller operation. minutes
Up min.
activates non-brightness-dependent switching
operation for the pre-set delay time.
Parallel circuit with automatic staircase lighting
switch remote control switch
Lighting switched automatic units Berker
control units.
Terminating outlet
The terminating outlet the Berker control unit fitted
with cable glands, for custom cable entries from
above, below, left, right and rear.
Up min. connected load.5 sec.
Operation relay contact maker
For potential-free and contacts and increase
switching capacity.
On time Delay time
Up min. 0.
90 min. switched back the brightness falls
below the pre-set value and there movement.
No switching operation the Berker control unit is
performed, because only the load switched off
