Návody k různým produktům Enika Nová Paka ...
Poznámky redaktora
1. Simultaneous blinking the LEDs "output" and "memory" confirms the
erasing all the transmitters
“long” depressing more than )
MAIN OFFER
Function the receiver:
ON After depressing the transmitter, the relay is
operated always, and remains operated
irrespective its prior condition
OFF After depressing the transmitter, the relay is
released always, and remains released
irrespective its prior condition
TIMER After depressing the transmitter, the relay is
operated for pre set time min.
The connection the receiver the mains (or its disconnection
from the same) can effected workers acquainted with the
job least, compliance with the Decree 50/1978 L. get the chosen transmitter ready
Logging the transmitter into the receiver and towing module
memory: i
Principle the entry:
■ repeated short depressing the push-button the receiver —'
(less than selection the operation from the main offer or
function
■ long depressing the push-button the receiver (more than s)
= confirmation the operation from the main offer function
■ any following depressing must effected within s
- after the elapse the receiver brought back Its initial
state repeat the entry procedure. control more appliances., declares that this DIN (H) in
compliance with the essential requirements and other relevant
provisions Directive 1999/5/EC. repeated short depressing the push-button the receiver select
"memory"
2.enika.cz)
H
LED signalling: 9alight flickering
During the entry:
OUTPUT I
MEMORY >
code entered already
During the operation:
i BAT. repeated depressing the push-button the receiver, select
"erase all", and keep the push-button depressed for more than s
2.) signalled simultaneous flickering the LEDs
"output" and "memory"
6./EXT
replace the battery the transmitter
that has transmitted last time
reception signals from the transmitter,
eventually interference
W !:
Hereby, Enika spol. necessary use the
appropriate number the Rn1 DIN towing modules.
Putting into service:
1. repeated short depressing the push-button the receiver, select
the function "timer" determined the combination the three
right hand side LEDs (see printing the receiver)
4. The equipment Is
designed for switchboard Installation using DIN strip. Within confirm long depression the push-button the
receiver
5. Within confirm long depression the push-button the
receiver
3. number modules row:
coverage with internal antenna:
connecting terminals dimension:
1000 VA
230 V/50 Hz
433,92 MHz
IP20
-10 +55 °C
224
21 for Rx1 DIN)
1 receiving towing
30 m
max. means pressing the receiver's button (for more than seconds),
check out the correctness the set shall signalled the
simultaneous flash "output" and "write" LEDs all Rn1 DIN towing
modules
5.5 sec. Depress twice (more than the respective push-button the
selected transmitter which you intend erase
Simultaneous flickering the LEDs "output" and "memory" confirms the
erasing the respective transmitter (the other ones remain the memory)
o c
?
1=1 J
Rxl DIN c
?
Rn1 DIN
.
Entry procedure:
1. 1,5 mm2
b) one transm itter
1.
Survey transmitters for the control the receiver
( actual list www.o. repeated short depressing the push-button the receiver, select
"memory"
2. number codes memory:
max. select the receiver's function repeated pressing the receiver's button
- the receiver's function determined the combination three
right hand side LEDs! (see receiver's legend)
4. r. Simultaneous flickering the LEDs "output", "memory" confirms that
the entry correct
Note: Proceed this way when entering the functions "ON", "OFF", "ON/
OFF", "PUSH BUTTON"
Entry the function "timer". Finish measuring the time depressing the push-button the
receiver
Erasing the transmitter:
a) all the transmitters
1. repeated depressing the push-button the receiver, select "erase
one code"
2. Depress twice (more than the respective push-button the
selected transmitter
6.
On DIN design (floating code), the ’’button” function
cannot used! This function substituted relay activation
for approximately 0.Rx1 (H) DIN single channel receiver
Rn1 DIN- towing module
“short” depressing less than )
Description:
The receiver can used control any single appliance with the help of
BOSys series. Depress twice (more than the respective push-button the
selected transmitter, and start measuring the time with watch
(I min.)
ON/OFF After depressing the transmitter, the relay is
switched the contrary position
PUSH BUTTON After depressing the transmitter, the relay is
operated, and remains operated
whilst the push-button the transmitter is
held depressed (max.
It forbiden any technical modifications the device. switching capacity:
power supply:
operating frequency:
IP protection:
operating temperature:
number codes/combinations:
max. connect the power supply
4.
The receiver cannot employed safety STOP push-button. put the appropriate number Rn1 DIN towing modules the
receiver's right (as close possible)
3. Within confirm long depression the push-button the
receiver
5.
Technical data: Rx1 DIN, Rx1 DIN, Rn1 DIN
max.
'The aerial shall hanged freely the space (not be
connected. s)
PUSH-BUTTON THE RECEIVER
If you face the coverage problems, connect
the Ext external receiver (It does not form
the part the equipment). Within confirm long depression the push-button the
receiver
3.G. Within confirm long depression the push-button the
receiver
3. fit the Rx1 DIN receiver the DIN strip
2. the external receiver used)
