The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
Poznámky redaktora
Lux
- Position corresponds approx.
In connection with other radio bus receivers (BLC radio buttons, radio switch
actuator adapters and built-in radio switch actuators flush-mounted etc.10 W
approx.g. A
approx. 100 free field
< mW
> billion
Yes
180°
16 m
approx.
This setting should selected when using the radio controller power section; the
activation brightness and the delay time can set the power section. 100 %
approx.42 MHz, ASK
30
> billion
Yes
according 55015
-25 °C
IP55
Screw-type terminals for max. transformers loading) incl.40 m
20 100 %
3 200 Lux %
less than Lux
to 200 Lux
-25 °C
IP55
Technical data
Battery type
Service life alkaline battery
Power consumption
Transmission frequency
Transmission range
Transmission power
Radio codes (assigned once per channel)
R&TTE approval (for and EFTA states)
Detection angle
Detection field
Mounting height
Response sensitivity
Brightness operating range
Sensor, activation brightness
Sensor, night triggering
Operating temperature
Index protection
Radio controller power pack surface-mounted order no.
Status LED red (flashes when sending)
Flashing: confirmation sending
Rapid flashing: low battery
Sensitivity setting
20 100 %Always follow the Radio Bus
planning instructions!
Because the Low Power
Technology, the controller
takes approx. Lux
On time approx.) the
controller triggers switching the load for minute (retriggering).
Combination extension available using
flat surface-mounted installation.
Radio controller 180
The detection beams
are optimally cut. after sending)
Transmission frequency
Transmission range
Transmission power
Radio codes (assigned once)
R&TTE approval (for and EFTA states)
Number channels
Detection angle
Detection field
Recommended mounting height
Response sensitivity
Response brightness
Operating temperature
Index protection
Installation height
Radio controller 180 flat order no. (free field)
< mW
> billion
Yes
1
180°
semi-oval approx. 9420.
wrong
Ensure that there are interference sources, e. to
become ready for operation.27 mW
Radio transmission mW
433.
Setting the activation brightness:
- Position
·brightness-independent
- Adjustment range approx.
For optimum detection the radio controller 180 should mounted laterally the direction
of movement. 2-3 years
battery flat, change it
433. Lux.), where they activate
the load for minute (retriggering).
The radio controller flat provided the backside with two potentiometers,
allowing the response sensitivity and activation brightness set. 1..) well appliance sockets with frame. 2. transformer power loss 1000 (inductive)
Fluorescent lamps uncompensated 1200 VA, parallel compensated 920 (induktive)
duo circuit 2300 (induktive)
Mixed load; capacitive and inductive loads should not mixed
max.
Lux
OFF ON
Radio bus
Phase connection
Load connection
Neutral conductor connection
Brightness setting approx.42 MHz, ASK
approx.)^ for hours
Long press button (>1sec.
Controller mounting
optimal not optimal
The detection beams are not cut. push-button (NCC contact) the
lead the radio controller power pack surface-mounted can used activate
additional functions. The response sensitivity each radio controller unit can
be adjusted varying detection conditions.
3 V=
1 lithium coin cell (type 2450 N)
approx.
Radio controller flat
The radio controller flat with integral brightness measurement allows the extension of
existing installations wireless transmission switching commands. sec.
The detection beams are not
optimally cut.
On detecting movement, the radio controller flat sends encrypted radio-telegram,
which understood and evaluated all radio receivers the radio bus system.42 MHz, (ASK)
max.
9 alkaline block battery 6LR61
approx. %
approx.5 mm2
110 mm
Technical data
Rated voltage
Switching contact
Switching capacity
Inrush current
Standby power consumption
Delay time
Brightness
Additional functions
Time between touch pulses
1st function
2nd function
3rd function
Reception frequency
Radio transmitters with teach-in facility
Radio codes (assigned once per channel)
R&TTE approval (for and EFTA states)
Radio interference suppression
Operating temperature
Index protection
Terminals
Dimensions H)
Surface-mounted radio controller
output stage
L N
Min. lamps heaters, the detection range.5 mm2
or 1.
Setting
response brightness
Setting
response sensitivity
CR 2032
3V
Sens. 2.1 m
approx.
The radio controller 180 flat can screwed stuck flat surface (wood, plaster,
glass, mirror etc. years
Daytime operation 0. The radio controllers can also be
taught-in other Radio Bus receivers (BLC radio button, radio adapter plug switch
actuator and radio switch actuators built-in/flush-mounted etc. The range is
reduced. min. Lux
5 °C
IP20
approx. 01740109. sec.
Technical data
Power supply unit
Battery type
Battery life
Rapid flashing the red LED (approx. mm
Radio controller 180 flat
Always follow the
Radio Bus planning
instructions!
The life the
battery halved, if
the potentiometer
is set ·Lux.: 1x
CR2450N
Supporting plate
TOP
Assembly
Radio bus controller/system
.) OFF for hours
Radio controller 180 order no.
Funk-Wächter 180 flach
9420
Batt. radio controller can taught-in any
number radio receivers. m
1. maximum radio controllers can taught-in
to radio controller power pack surface-mounted.T59
Rotating and
tilting possible
95°360°
Radio controller/system
The radio controller system cordless system, and particularly suitable for
upgrading existing installations. These functions can also used with taught-in hand-held or
wall-mounted radio transmitter follows. min.14 mW
Night time operation 0.
The controller detects the object
too late. 017509
230 V~, 50/60 Hz
Relay contact
230 Incandescent lamps and halogen lamps 2300 (ohmic)
Tronic transformer 1500 (capacitive)
Conv.
Teach-in switch
Always follow the Radio Bus
planning instructions!
Radio controller power pack
surface-mounted
SENS.
Short press button^ON for pre-set time
Short press button OFF (automatic mode remains active)
Long press button (>1sec. Lux %
with push-button (NCC contact)
600 ms
1 press for time
2 press for hrs %
3 press OFF for hrs %
433. min
