BERKER Wiring accessories + Building automation catalogue 2012

| Kategorie: Katalog  | Tento dokument chci!

The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.

Vydal: HAGER ELECTRO s.r.o. Autor: EN HAGER

Strana 552 z 616

Vámi hledaný text obsahuje tato stránku dokumentu který není autorem určen k veřejnému šíření.







Poznámky redaktora
14 W 0.137 17.281 kΩ 35 21. As result, drive runs the original direction again until the contact L2 reopened.3 kW Power consumption with night lowering 0.5 °C Switching temperature difference approx.g.279 66. RolloTec cutoff relays RMD are snapped onto the DIN hat profile rail. shut again after short time.277 kΩ The resistance values can only measured when the sensor is disconnected. Drive can still functioning, however, and actuates drive the opposite running direction means a feedback voltage via its capacitor.272 kΩ 25 33. Since the feedback voltage can 1000 and many switching position changes occur very short time, the limit position switch E2 overloaded. When laying the cable ducts when close high current conductors, shielded wires should used. Weld the contacts. 0. These switching operations cause pendulum motion the roller blind.75 mm² Cable length m Protection class according 60529 IP67 RolloTec Error parallel switching conventional tubular motors. – The following variants are available, depending the operating concept – RolloTec cutoff relay [2930] and RolloTec cutoff relay RMD [2931] for simultaneous movement two motors using one control section – RolloTec cutoff relay [2969] and RolloTec cutoff relay RMD [2919] with extension circuits for simultaneous movement two motors using one control section separate operation the individual motors. N Path feedback voltage N PE L PE E1 E4 Drive Drive 2 Wrong ! Figure Parallel-switched conventional tubular motors When the switch actuated, both drives are switched for the same running direction. 2034. Connect maximum 6-8 motors one miniature circuit-breaker (note current consumption).5 mm² cross section without influencing the precision the controller. 1 Drive 1 2 Drive 2 3 Junction box with cutoff relay 4 Junction box 5 RolloTec control section 2+PE 3+PE 5 4 3+PE 4+PE34 5 2 1 Figure Installation plan for cutoff relay Thermostat RolloTec cutoff relay . RolloTec cutoff relay RolloTec cutoff relays are mounted water-protected junction boxes or in deep flush-mounted sockets, e.085 kΩ 45 13.00 26.785 kΩ 15 52. Sensor characteristic values for the precise switch points: Measurement device with MΩ 5 85. The motors are destroyed. Connection for operation with sensor and timer L Outer conductor N Neutral conductor Load connection TA Resistor for night lowering the room temperature Timer (switch) for night lowering/temperature NTC connection for temperature sensor L N TA N NTC L Mains 0/1 230 V U = Load Heating Figure Wiring thermostat for underfloor heating, contact, with on/off switch and LEDs Technical data Thermostat for underfloor heating Order no.33 41.28 W Switches, 1-pole ON/OFF Contacts (relay) contact (for heating) not potential-free Temperature lowering approx.T35 The sensor cable can, necessary, extended using 2-wire cable of 1. behind blanking cover RolloTec insert.846 11. Temperature range °C Rated voltage 230 V~, 50/60 Hz; 230 V= Switching current (ohmic load) cos 1 Breaking capacity 2. The limit switch disabled this running direction. For joint control, use Berker cutoff relays electronic tubular motors, such those from Becker, Elero Selve. Motors roller blinds may be destroyed. When drive has reached the limit position, the limit position switch opens.. °C Sensor element NTC Sensor cable PVC 0. Overloading the limit switches through parallel switching of conventional tubular motors. Provide additional miniature circuit- breakers for extensions