The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
Poznámky redaktora
m
2.
Load off Last on
Monitored area too dark:
Load remains switched during motion. transformer, inductive load
500 Fluorescent lamps uncomp.
Mount brightness sensor the side
away from windows avoid the
effects scattered light.
LED
flashes
Monitored area light
enough:
Load remains off even when
motion detected. Only after minutes without motion being
detected the slide show function ended automatically. 2.
Cooling light bulbs and air movements from fans,
heaters and open windows can detected and
lead switching again. the presence detector detects motion the next minutes,
then the switch-off time extended.
Lighting switched off
for minutes.
- for all presence detectors the brightness their monitored area constantly
exceeds least twice the set value. 100 m
103 57.
When motion detected and the brightness below adjustable brightness
threshold, the load switched on.5 mm²
Brightness sensor
Delay time setting
Brightness setting
Test and status LEDs
(brightness settings help)
Fresnel lens
test
10s
10min
30min
time
0
lux
During installation, not subject the presence detector direct sunlight;
this could destroy the detector. sec.
Detection field on
the floor
1 m0
Technical data
Rated voltage
Connected load
Power consumption
Delay time
Brightness threshold value
Detection angle
Detection levels
Number zones
Number switching segments
Detection area desk level
Detection area floor level
Installation height for nominal detection areas
Number extension units
Extension unit cable length
Connection parallel
Load cable length (with parallel connection cable)
Dimensions H)
Radio interference suppression
Operating temperature
Connecting terminals
Presence detector surface-mounted order no. this, switch
the lighting again the extension unit within minute after switched off
automatically. also able evaluate small
motions (fine motor functions), such those that typically occur offices.
Sources interference
Do not install the direct vicinity heat source. presence detectors) with extension units
Push-button (NOC)N
L
N μ
BK GY
L μ
BK GY
L 1
for illuminated push-buttons
neutral conductor
necessary
5031
Operation with extension units
Push-button (NOC)
to additional
extension units
N
L
N μ
BK GY
L 1
for illuminated push-buttons
neutral conductor necessary
Presence detector surface-mounted
L
N
L
N
to additional
extension units
1839
Mechanical
push-button
The lighting switched The delay time
corresponds the value set the
potentiometer, but least minutes
Detected motions extend the delay time to
the time set the potentiometer. The delay time is
restarted every time motion detected the respective presence detector
surface-mounted.
In this manner possible set presence detector system with equal rights
without mutual influence.
daylight), then you can switch the brightness evaluation off manually. 400 lux), for example due
to brighter daylight, then the red diagnosis and settings help LED flashes and the
presence detector switches off after minutes the latest, even there motion.
With motion the switch turned off
after the set delay time. 55015
approx. °C
Screw terminals for max. When set to
the marking the presence detector can only switched via the
extension unit. presence detector mode
approx.
Load remains switched during motion. W
approx. sec.T18
4 m
H=2,50 m
2,5 m
Presence detector surface-mounted
The presence detector surface-mounted used monitor presence indoor areas. m
approx. The
presence detector surface-mounted can only used for switching applications.
The potentiometer "lux" can used adjust the minimum brightness
from approx.
Temporary deactivation the brightness evaluation
If the presence detector switched the lighting off due sufficient extraneous light (e. It
is mounted exclusively ceilings, and monitors the area located below it.
Presence detector, surface-mounted
.
Expansion the detection area
Connection parallel presence detectors surface-mounted "intelligent load linking"
Note: All presence detectors connection parallel surface-mounted must operated
in the same phase.
Brightness threshold value
Minimum brightness the area being monitored. the brightness the monitored surface continuously exceeds
double the set brightness threshold value (but least approx. Can adjusted without dismantling. 170108
230 V~, 50/60 Hz
1000 incandescent lamps and 230 halogen lamps, ohmic load
750 halogen lamps with Tronic transformer, capacitive load
750 halogen lamps with conv. test mode; approx.
With motion the switch turned off
after the set delay time. When the brightness drops
below the set brightness threshold value and there motion, then the
switch turned on. The built-in microprocessor, connection with voltage measurement the load
cable, ensures that all presence detectors connected parallel surface-mounted detect
when lighting switched on. sec. motion detected now, the
lighting may switched again, depending the brightness situation. Connection parallel does not increase the max.
Slide show function
With BLC extension unit mechanical push-button (NOCs) possible switch
the lighting off selectively. sec.
5031
Connection parallel (max. setting "test"
Presence mode: approx. more motion detected, then the load switched after
the set delay time.10 lux (symbol moon) 1000 lux (symbol sun).
Delay time
The potentiometer "time" can used for fine adjustment the on-time. min. 100 m
possible
max.g.5 m
Push-button contact unlimited
max.
The lighting switched off when:
- none the presence detectors detecting movement and the last remaining on-time
has expired.5 mm² 1.
Monitored area light enough due switched-on
lighting. 10-1000 lux symbol "0" initial activation only via extension unit
360°
6
80
320
approx.5 mm
acc.
The lighting now remains switched long the presence detector detects motion. minutes, because
the brightness sufficient even without lighting.
Monitored area very bright with lighting and
extraneous light:
Load switches off after approx. approx.
For more information,
see slide show function
Load off Load on
Extension unit operation
Test LED (brightness settings help)
LED
off
Monitored area too dark:
Load switched when
motion detected. connected
load. necessary limit
detection area using supplied push-on cover
Settings
The cover can removed order adjust the delay time
and brightness. you wish to
end the slide show function manually, switch the lighting again manually the
extension unit (for dimmer inserts the brightness before switching-off will set). inductive load
1000 fluorescent lamps duo configuration, inductive load
Mixed load, capacitive and inductive loads should not mixed
approx. responds to
heat motions caused persons, animals objects.
LED
on
Monitored area light
enough:
Load remains off even when
motion detected. The brightness evaluation now active again. this case the switch-off brightness 400 lux. The device remains switched long further
motions are detected.
The lighting only switched off the presence detector does not detect any more
motion and the delay time has elapsed. min. long motion detected one the presence
detectors surface-mounted, the lighting remains switched on.
Test mode: approx
