The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
Poznámky redaktora
Only after minutes without motion being
detected the slide show function ended automatically.
For more information,
see slide show function
Load off Load on
Extension unit operation
Test LED (brightness settings help)
LED
off
Monitored area too dark:
Load switched when
motion detected. °C
Screw terminals for max. approx.
Brightness threshold value
Minimum brightness the area being monitored.
The potentiometer "lux" can used adjust the minimum brightness
from approx. The device remains switched long further
motions are detected.
Slide show function
With BLC extension unit mechanical push-button (NOCs) possible switch
the lighting off selectively. presence detector mode
approx.
- for all presence detectors the brightness their monitored area constantly
exceeds least twice the set value. W
approx.
With motion the switch turned off
after the set delay time. When set to
the marking the presence detector can only switched via the
extension unit.
Test mode: approx. responds to
heat motions caused persons, animals objects.
When motion detected and the brightness below adjustable brightness
threshold, the load switched on.
Load off Last on
Monitored area too dark:
Load remains switched during motion. sec. necessary limit
detection area using supplied push-on cover
Settings
The cover can removed order adjust the delay time
and brightness. more motion detected, then the load switched after
the set delay time.g. 2.
Monitored area very bright with lighting and
extraneous light:
Load switches off after approx.
In this manner possible set presence detector system with equal rights
without mutual influence. When the brightness drops
below the set brightness threshold value and there motion, then the
switch turned on. 400 lux), for example due
to brighter daylight, then the red diagnosis and settings help LED flashes and the
presence detector switches off after minutes the latest, even there motion. transformer, inductive load
500 Fluorescent lamps uncomp. setting "test"
Presence mode: approx. presence detectors) with extension units
Push-button (NOC)N
L
N μ
BK GY
L μ
BK GY
L 1
for illuminated push-buttons
neutral conductor
necessary
5031
Operation with extension units
Push-button (NOC)
to additional
extension units
N
L
N μ
BK GY
L 1
for illuminated push-buttons
neutral conductor necessary
Presence detector surface-mounted
L
N
L
N
to additional
extension units
1839
Mechanical
push-button
The lighting switched The delay time
corresponds the value set the
potentiometer, but least minutes
Detected motions extend the delay time to
the time set the potentiometer. inductive load
1000 fluorescent lamps duo configuration, inductive load
Mixed load, capacitive and inductive loads should not mixed
approx.
Detection field on
the floor
1 m0
Technical data
Rated voltage
Connected load
Power consumption
Delay time
Brightness threshold value
Detection angle
Detection levels
Number zones
Number switching segments
Detection area desk level
Detection area floor level
Installation height for nominal detection areas
Number extension units
Extension unit cable length
Connection parallel
Load cable length (with parallel connection cable)
Dimensions H)
Radio interference suppression
Operating temperature
Connecting terminals
Presence detector surface-mounted order no. The
presence detector surface-mounted can only used for switching applications. Connection parallel does not increase the max. sec.
Cooling light bulbs and air movements from fans,
heaters and open windows can detected and
lead switching again. this, switch
the lighting again the extension unit within minute after switched off
automatically.
Temporary deactivation the brightness evaluation
If the presence detector switched the lighting off due sufficient extraneous light (e.
Delay time
The potentiometer "time" can used for fine adjustment the on-time.
The lighting only switched off the presence detector does not detect any more
motion and the delay time has elapsed. min.
daylight), then you can switch the brightness evaluation off manually. test mode; approx. m
2. 100 m
103 57. also able evaluate small
motions (fine motor functions), such those that typically occur offices. sec. 10-1000 lux symbol "0" initial activation only via extension unit
360°
6
80
320
approx. It
is mounted exclusively ceilings, and monitors the area located below it.
Presence detector, surface-mounted
. the presence detector detects motion the next minutes,
then the switch-off time extended.
Mount brightness sensor the side
away from windows avoid the
effects scattered light. the brightness the monitored surface continuously exceeds
double the set brightness threshold value (but least approx.
Monitored area light enough due switched-on
lighting.
LED
flashes
Monitored area light
enough:
Load remains off even when
motion detected. sec. The delay time is
restarted every time motion detected the respective presence detector
surface-mounted.5 mm²
Brightness sensor
Delay time setting
Brightness setting
Test and status LEDs
(brightness settings help)
Fresnel lens
test
10s
10min
30min
time
0
lux
During installation, not subject the presence detector direct sunlight;
this could destroy the detector.5 m
Push-button contact unlimited
max.
Lighting switched off
for minutes. minutes, because
the brightness sufficient even without lighting.
The lighting now remains switched long the presence detector detects motion.T18
4 m
H=2,50 m
2,5 m
Presence detector surface-mounted
The presence detector surface-mounted used monitor presence indoor areas. The built-in microprocessor, connection with voltage measurement the load
cable, ensures that all presence detectors connected parallel surface-mounted detect
when lighting switched on. you wish to
end the slide show function manually, switch the lighting again manually the
extension unit (for dimmer inserts the brightness before switching-off will set).
LED
on
Monitored area light
enough:
Load remains off even when
motion detected. this case the switch-off brightness 400 lux.
Sources interference
Do not install the direct vicinity heat source.
Expansion the detection area
Connection parallel presence detectors surface-mounted "intelligent load linking"
Note: All presence detectors connection parallel surface-mounted must operated
in the same phase.5 mm
acc. m
approx.
5031
Connection parallel (max.10 lux (symbol moon) 1000 lux (symbol sun). The brightness evaluation now active again.
With motion the switch turned off
after the set delay time.
The lighting switched off when:
- none the presence detectors detecting movement and the last remaining on-time
has expired. long motion detected one the presence
detectors surface-mounted, the lighting remains switched on.
Load remains switched during motion. 170108
230 V~, 50/60 Hz
1000 incandescent lamps and 230 halogen lamps, ohmic load
750 halogen lamps with Tronic transformer, capacitive load
750 halogen lamps with conv.5 mm² 1. motion detected now, the
lighting may switched again, depending the brightness situation. connected
load. min. 55015
approx. Can adjusted without dismantling. 100 m
possible
max
