Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
107(at 120 cpm)
Electrical*4
<Resistive load>
Min. 7.O. (Not freezing and condensing low temperature)
Mass Single type: approx. Please contact for details.8V DC
(Initial)
75 160Q 900 16V DC
Max.5 . 85% R.23 oz
Notes:
*1.8V DC
(Initial)
54. recommend that you confirm operation under actual conditions. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. 0. 3. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min. Therefore, please inquire when using with circuit that causes energized condition both sides simultaneously.6V DC
(Initial)
109 110Q 1,309 mW
12V DC
Max.5s OFF
Conditions Conditions for operation, transport and storage*2
High heat-resistant/Pin Paste type Ambient temperature: -40°C +110°C -40°F +230°F,
Humidity: R. (Detection current: 10mA)
Operate time (at nominal voltage) Max.This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. Refer “Usage ambient condition“ on
page 178.)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min.
94 61284 te: 010113J
. 6.1 m/s2{4. 105(25 14V motor lock condition), operating frequency: 0. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max.: Typ5mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) N.H. Also, this does not guarantee repeated switching.7V DC
(Initial)
Min.
*3.(ACTE)
RATING
1.5V type)
655 (Pick-up voltage 7.The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value.12 oz, Twin type: approx.5 .: Typ4mQ, N.C.
*4.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F). 44.5V DC
(Initial)
Min.: 10A 14V DC
Max. 6.H.O. 0. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form 2
Contact resistance (Initial) N.5V type)
900 (Pick-up voltage 6.Do not use for lamp loads, electric discharge lamp loads, any other lamp loads and capacitor loads. carrying current (12V initial)*3 25A for minutes (at 20°C 68°F)
Nominal operating power
1,309 (Pick-up voltage 5.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min.1 m/s2{4.Depends connection conditions. 5.C.5V DC
(Initial)
Min.5 220Q 655 mW
2.
* the relay used continuously for long periods time with coils both sides energized condition, breakdown might occur due abnormal heating depending on
the carrying condition. Coil data
Nominal coil
voltage
Pick-up voltage
(at 20oC 680F)
Drop-out voltage
(at 20°C 68°F)
Nominal operating
current
[+10%] (at 20°C 68°F)
Coil resistance
[+10%] (at 200C 68oF)
Nominal operating
power
(at 20°C 68°F)
Usable voltage range
Max. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min.5s ON, 9.: 20A 14V DC, N. 100 (at 500V DC, Measurement same location “Breakdown voltage” section. 0. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 44.
*2.7V type)
Min. 105 (at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
Min.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial) (without protective element)
Mechanical
characteristics
Shock resistance
Functional Min
