Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
)
Destructive Min. 5ms) (Nominal operating voltage applied the coil, excluding contact bounce time.42oz SMA type: Approx. 20g .5GHz type only.) 0. 100mQ (By voltage drop 10V 10mA)
Rating
Contact input power (CW) Max.7 0.; max. (Detection current: 10mA)
Time characteristics
(at 20°C 68°F)
Operate time (Set time) Max.5 0.R. The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value.R.)
Vibration
resistance
Functional double amplitude 3mm (Detection time: 10^s.5 1. 50W (at 3GHz) (V. 15ms (approx.
*5.
*2. 15ms (approx.7 1.
*4.4 1. 18GHz characteristics can applied 18GHz type only.S.4 0.)
Release time (Reset time)
Max.4
GHz*3
12. 106(at 180 cpm)
Electrical (Hot switch) Min.W.)
Destructive double amplitude 5mm/15 2,000 [W0 2.4 18
GHz*4
18 26.R. 105(1W High frequency load, 3GHz, impedance 50Q, V.5 0.(ARV)
2.5GHz characteristics can applied 26.W. Specifications
Characteristics Item Specifications
Contact
Arrangement SPDT
Contact material Gold plating
Contact resistance (Initial) Max.8
Isolation (dB, min. (Detection current: 10mA)
Between contact
and coil
500 Vrms for min.W.4 18
GHz*3
to GHz
8 12.8
Insertion loss (dB, max.71oz
Notes: *1. 1. Refer “NOTES” page 49. Factors such heating the connected terminal influence the high frequency characteristics; therefore, please verify under actual conditions use. (max.) 1. 1,000 (at 500 DC) Measurement same location “breakdown voltage (Initial)” section. 1.
*6.3 1.5
GHz*5
V. 26.3 0. (Detection current: 10mA)
Between contact
and earth terminal
500 Vrms for min.6 1. 500 m/s2(Half-wave pulse sine wave: 11ms, detection time: 10^s.94 (m/s2)2/Hz]
Expected life
Mechanical Min. 1,000 m/s2(Half-wave pulse sine wave: 6ms.3) (at cpm)
Conditions
Conditions for operation,
transport and storage*6
Ambient temperature: -55oC +85oC -6
Humidity: 85% R.S. 18GHz characteristics can applied 18GHz and 26.35 1.7 1.3 less, contact switching, ambient temperature 20oC 68oF)*1
Nominal operating power 700mW
High frequency
characteristics
(Impedance 50Q)
PIN type*2 SMA type
Frequency GHz GHz
8 12. 5ms) (Nominal operating voltage applied the coil, excluding contact bounce time. 12g .3 0.7 0.S. (Detection current: 10mA)
Between coil and
earth terminal
500 Vrms for min.)
(without diode, only for Release time)
Mechanical
characteristics
Shock
resistance
Functional Min. (Not freezing and condensing low temperature)
Air pressure: 106 kPa
Unit weight PIN type: Approx.
46 61315 rv: 010611J
. Measuring method: After installing dedicated inspection equipment
*3.4
GHz*4
12.H.) 50
Electrical
characteristics
Insulation resistance (Initial) Min.
Breakdown
voltage
(Initial)
Between open
contacts
500 Vrms for min.5GHz types only
