Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
: Typ4mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) N. 7.
High heat-resistant/Pin Paste type Ambient temperature: -40°C +110°C 40°F +230°F,
Humidity: R.C.35 oz
Notes:
*1.5s ON, 9. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min.
*4. Coil data
1) Standard type
Nominal coil
voltage
Pick-up voltage
(at 200C 680F)
Drop-out voltage
(at 20°C 68°F)
Nominal operating
current
[+10%] (at 20°C 68°F)
Coil resistance
[+10%] (at 200C 68OF)
Nominal operating
power
(at 20°C 68°F)
Usable voltage range
Max. .C.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min. Please contact for details. 105(at (inrush), 12A (steady), DC), Operating frequency: ON, 14s OFF
Conditions Conditions for operation, transport and storage*2
Standard type Ambient temperature: -40°C +85°C -40°F +185°F,
Humidity: R.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F). (Detection current: 10mA)
Operate time [Set time] (at nominal voltage) Max.5s OFF
<Lamp load> *4
Min.Depends connection conditions.)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. 7.
2) coil latching type
Nominal coil
voltage
Set voltage
(at 200C 68OF)
Reset voltage
(at 200C 680F)
Nominal operating current
[+10%] (at 200C 680F)
Coil resistance
[+10%] (at 200C 680F)
Nominal operating power
(at 200C 680F) Usable voltage range
Set coil Reset coil Set coil Reset coil Set coil Reset coil
12V DC
Max.5V DC
(Initial)
53.5V type)
900 (Pick-up voltage 7. 7. 0.H.The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value.
ds 61282 tc: 310113D 87
Automotive
.0V type)
640 (Pick-up voltage 7. carrying current (12V initial)*3 35A for hour (at 20°C 68°F)
Nominal operating power
1,309 (Pick-up voltage 6.0V DC
(Initial)
Min. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min. 0.H. 85% R.2V DC
(Initial)
Max. 85% R.5V type)
1,920 coil latching type)
Min.5V DC
(Initial)
Min.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical
Min. 44.3 225Q 640 mW
Note: Other pick-up voltage types are also available.: Typ3mQ, N.O.When using with electric discharge lamp load any other lamp load, capacitor load, connect COM the (plus)” side. 44. 105(at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
Min. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 0.5V DC
(Initial)
Min.This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load.(ACTC)
RATING
1. 107(at 120 cpm)
Min.5V DC
(Initial)
75 160Q 900 16V DC
Max. 106(at 120 cpm) coil latching type)
Electrical
<Resistive load>
Min. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time [Reset time] (at nominal voltage) Max. 105(30 14V motor lock condition), operating frequency: 0.
(Not freezing and condensing low temperature)
Mass Approx.H.O. recommend that you confirm operation under actual conditions. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial) (without protective element)
Mechanical
characteristics
Shock resistance
Functional Min. Also, this does not guarantee repeated switching.5V DC
(Initial)
109 110Q 1,309 mW
12V DC
Max.: 30A 14V DC, N. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form Double make contact Form A
Contact resistance (Initial) N.
*2.1 m/s2{4. 100 (at 500V DC, Measurement same location “Breakdown voltage” section.: 15A 14V DC
Max. 6. Refer “Usage ambient condition“ on
page 178.
Refer “Usage ambient condition“ page 139.2V DC
(Initial)
160 160 75Q 75Q 1,920 1,920 16V DC
2. 7.1 m/s2{4.
*3.H
