Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial) (without protective element)
Mechanical
characteristics
Shock resistance
Functional Min.1 m/s2{4.: Typ3mQ, N.176 oz, Twin type: approx.1 m/s2{4. the (plus)” side. Therefore, please inquire when using with circuit that causes energized condition both sides simultaneously. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 107(at 120 cpm)
Electrical
<Resistive load>
Min. 85% R.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min.
* the relay used continuously for long periods time with coils both sides energized condition, breakdown might occur due abnormal heating depending on
the carrying condition. 105 (at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
Min.O.)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min.
*2.
High heat-resistant/Pin Paste type Ambient temperature: -40°C +110°C -40°F +230°F,
Humidity: R.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min.Depends connection conditions.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F).7V type)
Min.H. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min.This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. Refer “Usage ambient condition“ on
page 178.: 10A 14V DC
Max. (Detection current: 10mA)
Operate time (at nominal voltage) Max.Part numbers for electric discharge lamp loads any other lamp loads and for capacitor loads only consist “ACTB*L**”. carrying current (12V initial)*3 25A for minutes (at 20°C 68°F)
Nominal operating power
1,440 (Pick-up voltage 5. 85% R.
(Not freezing and condensing low temperature)
Mass Single type: approx.5V type)
900 (Pick-up voltage 6. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form Form 2
Contact resistance (Initial) N. Please contact for details.C.5V type)
640 (Pick-up voltage 7.5 .The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value.
When using the lamp control type, connect N.
*3. Also, this does not guarantee repeated switching.: 20A 14V DC, N.335 oz
Notes:
*1.H.C. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max.
80 61280 tb: 010113J
.O.: Typ4mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) N.H.O. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min.5s ON, 9. 105(at (inrush), (steady), DC), Operating frequency: ON, 14s OFF
Applies only lamp control type
Conditions Conditions for operation, transport and storage*2
Standard type Ambient temperature: -40°C +85°C -40°F +185°F,
Humidity: R. 105(25 14V motor lock condition), operating frequency: 0. 44.H. 44.5s OFF
<Lamp load>*4
Min. 9.
*4. 100 (at 500V DC, Measurement same location “Breakdown voltage” section.(ACTB)
2. recommend that you confirm operation under actual conditions
