Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Coil holding voltage the coil voltage after 100 from the applied nominal voltage. 200 m/s2{Min.67 Approx. switching power (resistive load) 1,500VA, 180W
Max.SF-Y
2.H.,^ 8
N 4
N -------- oiO ---------O10
N 5
NO1
N 2
N 3
N 4
N 5
N 6
•—01. Harmful substances the contacts are removed gas purging before sealing with. (at nominal voltage)
Unit weight Approx. (Detection current: 10mA)
Between contact sets 4,000 Vrms for min.
*3. According 61810-1:2010, table Characteristic sealed construction with terminals, case and base sealed shut with sealing resin.
Important: Relay characteristics may influenced by:
• strong external magnetic fields
• magnetic conductive materials near the relay
• narrow top-to-top mounting (printed surface printed surface)
Insulation
2 Form Form Form Form Form Form Form Form B
N ---------04 ---------04
N 2
N --------- 50---------
N 3
C il
1? f
C il
1? il
N . switching capacity (Reference value)*1 10mA 10V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 1,000 m/s2(Half-wave pulse sine wave: ms)
Vibration
resistance
Functional double amplitude 1. The upper limit the ambient temperature the maximum temperature that can satisfy the coil temperature rise value. 20G} (Half-wave pulse sine wave: ms; detection time: 10|as)
Destructive Min. 1,000MQ (at 500V DC) Measurement same location “Breakdown voltage” section.)
- Basic insulation: overvoltage category III, pollution degree 250V AC
(The clearance .059 inch (Detection time: 10|as)
Destructive double amplitude 1. Construction designed to
prevent seeping flux when soldering and cleaning fluid when cleaning.217 inch more clearance and creepage distance
even between contact NO4 and coil. switching voltage 250V AC, 30V DC
Max. Specifications
Characteristics Item
Specifications
4-pole 6-pole
Contact
Contact arrangement Form Form Form Form Form Form Form Form B
Forcibly guided contacts All contacts: Type 50205
Contact resistance (Initial) Max.
*2..118 inch more between all contacts and the creepage distance .)
Degree protection III*3
Conditions
Conditions for operation, transport and
storage*2
Ambient temperature: -400C +700C
Humidity: 85% R. . This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. Refer Usage, transport and storage conditions
in NOTES see page 607.118 inch more and the creepage distance . 20ms (Nominal coil voltage applied the coil, excluding contact bounce time)
Release time (at 200C 680F) Max. Operating speed times/min.
Breakdown
voltage (Initial)
Between open contacts 1,500 Vrms for min.157 inch more.
*4.5 . .217 inch more between all contacts. (Not freezing and condensing low temperature)
Max.5 .059 inch
Expected life
Mechanical Min.
C oil
•-ot
N ■—012 •—012
= Reinforced insulation: overvoltage category III, pollution degree 250V AC
(Clearance and creepage distance 5.157 inch more. switching current A
Min. 107(at 180 times/min. (Detection current: 10mA)
Between contact and coil NC3: 2,500 Vrms for 1min; NO4: 4,000 Vrms for 1min (Detection current: 10mA)
Coil holding voltage*4 Min.81 oz
Notes:
*1. 105(at times/min. 60%V (Initial, 200C 680F)
Operate time (at 200C 68°F) Max.5 . 100 (By voltage drop 1A)
Contact material Gold-flashed AgNi alloy type
Rating
Nominal switching capacity (resistive load) 250V AC, 30V DC
Max. Even between contact NC3 and coil, the
clearance . Also, there 5.5 . 10ms (Nominal coil voltage applied the coil, excluding contact bounce time) (without diode)
Mechanical
characteristics
Shock
resistance
Functional Min.)
ds_61411_en_sfy: 200213D 603
Safety
.)
Electrical 250 resistive load: Min.
