Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
8Wtype 20A)
Min. The upper operation ambient temperature limit isthe maximum temperature that can satisfy the coil temperature rise value. 100 m/s2{10G}
(Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min.)
Conditions
Conditions for operation, transport and
storage*2
Ambient temperature: -30°C +80°C 22°Fto +176°F,
Humidity: R.09 oz
Notes:
*1.8 Wtype) continuous continuous
Nominal operating power 1.) Min.4 V
(by voltage drop
12V A)
Contact material alloy (Cadmiumfree)
Rating
Nominal switching capacity (resistive load)
20 12V (1. (Not freezing and condensing lowtemperature)
Max. 106(at 120times/min. 0. Refer “6. MQ
(at 500V DC, Measurement same location as
“Breakdown voltage” section.4Wtype)
30 for 1min. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626).3 V
[by voltage drop
12 (1. (Detection current: 10mA)
Between contacts and coil 500 Vrms for 1min. 44.8 Wtype)]
Max. (at 500V DC,
Measurement same
location “Breakdown
voltage” section. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial)
Min. 200 m/s2{20G}
(Half-wave pulse sine wave: 11ms;
detection time: 10|as)
Min.67 oz
31 1. 0. 0.4 W/1.H. Thisvaluecanchangeduetotheswitchingfrequency, environmental conditions, anddesired reliability level, therefore isrecommendedtocheckthiswiththeactual load. 85% R. 104(operating frequency: 3s
ON, 15s OFF) (1.8W
Min. (at nominal switching capacity)
Water-proof
standard
Water-proof standard Sealed type: JIS D0203 S2, Dust cover type: JIS D0203 R2
Mass Rubber bracket Atype: . operating speed 15times/min.8Wtype: 20A)
15times/min. 100 m/s2{10G}
Screw-mounting and direct coupling type: Hz, Min. 10ms (at nominal voltage) (excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock
resistance
Functional
Min.)
Min.4W and 1.CA
2. 105(operating frequency: ON,
2s OFF) (1.8Wtype) 20A 12V DC
Max.H.4Wtype: nominal load,
1.
516 61201 ca: 010113J
. 105(at 120times/min.4Wtype)
30 12V (1.5G} (Detection time: 10|as)
Destructive
Rubber bracket type: Hzto 500 Hz, Min. 100 m/s2{10G}
Screw-mounting and direct coupling type: Hz, Min. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration
resistance
Functional
Rubber bracket type: Hzto 500 Hz, Min.4 Wtype),
12 (1.
*2.81 oz,
Screw-mounting and direct coupling type: .8 1.8Wtype A)
Min. (1. (Detection current: 10mA)
Operate time (at 20°C 68°F) Max.5G},
Time ofvibration for each direction; direction: hours, direction: hours
Expected life
Electrical (at nominal switching capacity)
Min.3 V
(by voltage drop
12 A)
Max. 44.)
Breakdown
voltage (Initial)
Between open contacts 500 Vrms for 1min. 105(operating frequency: ON, OFF)
Mechanical Min. carrying current
(at coil applied voltage DC, 80°C 176°F)
20 continuous (1. Specifications
1) e
Characteristics Item
Specifications
1Form Atype 1Form Btype Form Ctype
Contact
Arrangement 1FormA Form 1Form C
Contact resistance (Initial) Typ 3mQ (By voltage drop 1A)
Contact voltage drop (after electrical life test)
Max.1 m/s2{4. 10ms (at nominal voltage) (excluding contact bounce time) (Initial)
Release time (at 20°C 68°F) Max.1 m/s2{4. (1