Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
44.
*3. Refer “6.35 oz
Notes:
*1.1 m/s2{4. 100 (at 500V DC, Measurement same location “Breakdown voltage” section. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min.O.
(Not freezing and condensing low temperature)
Mass Approx.5V DC
(Initial)
Min.5V DC
(Initial)
109 110Q 1,309 mW
12V DC
Max.5V type)
1,920 coil latching type)
Min. Also, this does not guarantee repeated switching. 6. 105(at (inrush), 12A (steady), DC), Operating frequency: ON, 14s OFF
Conditions Conditions for operation, transport and storage*2
Standard type Ambient temperature: -40°C +85°C -40°F +185°F,
Humidity: R. 7.: 15A 14V DC
Max.: Typ4mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) N.5V DC
(Initial)
53. 85% R.
*2.1 m/s2{4.C.The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value. Coil data
1) e
Nominal coil
voltage
Pick-up voltage
(at 200C 680F)
Drop-out voltage
(at 20°C 68°F)
Nominal operating
current
[+10%] (at 20°C 68°F)
Coil resistance
[±10%] (at 200C 68OF)
Nominal operating
power
(at 20°C 68°F)
Usable voltage range
Max.
ds 61282 tc: 060313J 489
Automotive
.When using with electric discharge lamp load any other lamp load, capacitor load, connect COM the (plus)” side. (Detection current: 10mA)
Operate time [Set time] (at nominal voltage) Max. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time [Reset time] (at nominal voltage) Max.)
Min. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 105(30 14V motor lock condition), operating frequency: 0. 106(at 120 times/min. 0.O.(ACTC)
RATING
1.Depends connection conditions. 0. carrying current (12V initial)*3 35A for hour (at 20°C 68°F)
Nominal operating power
1,309 (Pick-up voltage 6. 44.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min.: Typ3mQ, N. 7. 107(at 120 times/min.) coil latching type)
Electrical
<Resistive load>
Min.5s ON, 9.5V DC
(Initial)
75 160Q 900 16V DC
Max.H.: 30A 14V DC, N.3 225Q 640 mW
Note: Other pick-up voltage types are also available.5V type)
900 (Pick-up voltage 7.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical
Min.2V DC
(Initial)
Max. 7.C.H. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form Double make contact Form A
Contact resistance (Initial) N.H. . 0.
High heat-resistant/Pin Paste type Ambient temperature: -40°C +110°C 40°F +230°F,
Humidity: R.)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min. 105(at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
Min.
2 e
Nominal coil
voltage
Set voltage
(at 200C 68OF)
Reset voltage
(at 200C 680F)
Nominal operating current
[±10%] (at 200C 680F)
Coil resistance
[±10%] (at 200C 680F)
Nominal operating power
(at 200C 680F) Usable voltage range
Set coil Reset coil Set coil Reset coil Set coil Reset coil
12V DC
Max.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F).This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load.
*4. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial) (without protective element)
Mechanical
characteristics
Shock resistance
Functional Min. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min. Usage, Storage and Transport
Conditions” AMBIENT ENVIRONMENT (page 626).0V DC
(Initial)
Min.5V DC
(Initial)
Min.0V type)
640 (Pick-up voltage 7. Please contact for details. 85% R. 7.2V DC
(Initial)
160 160 75Q 75Q 1,920 1,920 16V DC
2.H. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min.5s OFF
<Lamp load> *4
Min. recommend that you confirm operation under actual conditions
