Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
5s ON, 9.O. . (Not freezing and condensing low temperature)
Max. 105 (at nominal switching capacity)
(operating frequency: ON, OFF)
<Motor load>
Min. 85% R.O.C.: (at 20°C 68°F for minutes), (at 20°C 68°F for hour),
30 (at 85°C 185°F for minutes), (at 85°C 185°F for hour)
Nominal operating power 640 mW
Min.
REFERENCE DATA
1.C.
*3.
*2.: 14V DC
N.: 14V DC
Max. 105(at Inrush 25A, Steady DC)
Min.5s OFF)
Conditions
Conditions for operation, transport and
storage*2
Ambient temperature: -40°C +85°C -40°F +185°F,
Humidity: R. 107(at 120 cpm)
Electrical
<Resistive load>
Min.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min. 105(at 20A brake currect)
(operating frequency: 0. carrying current (12V DC)*3
N. 44. (Detection current: 10mA)
Operate time (at nominal voltage) Max.1 m/s2{4. The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value. 105 (at nominal switching capacity)
N.H. Depends connection conditions. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max.JJ-M
2. 44.H. (Detection current: 10mA)
Between contacts
and coil
500 Vrms for min. 100 (at 500V DC, Measurement same location “Break down voltage” section)
Breakdown
voltage (Initial)
Between open
contacts
500 Vrms for min. 105 (at Inrush 25A, Steady V
DC), Min. bient tem perature and operating voltage
range
40
0 35
D
>
oî 30
CD
S3
1 25
I 20
Q.5s ON, 9. itching capability
(Resistive load, initial)
(N.: Min. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min.C.176 oz
Notes:
*1.5s OFF)
<Resistive load>
N. Refer “Usage ambient condition“ on
page 178. 105 (at nominal switching capacity)
(operating frequency: ON, OFF)
<Motor load>
N. Coil tem perature rise
Sample: JJM1-12V, 6pcs
Point measured: Inside the coil
Contact current: Non current through
contact, 5A, 10A, 15A, 20A
Resistance method, ambient temperature 85°C 185°F
2.O. recommend that you confirm operation under actual conditions. 104 (at 20A motor lock)
N.: Min.: Min.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F). Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form C
Contact resistance (Initial) Typ 5mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity
(resistive load)
20 14V DC
N.O. Also, this does not guarantee repeated switching. Max. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock
resistance
Functional Min.: Min. operating speed cpm (at nominal switching capacity)
Mass Approx. side: room temperature)
3. switching capacity
(resistive load)*1
1 12V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration
resistance
Functional 100 Hz, Min.O. 104 (at 20A motor lock)
(operating frequency: 0.1 m/s2{4.
CD
^ 15
10
5
0
X /
/ /
/ /
/ /
/ /
/ /
/ /
/ /
/ /
"Pick
(col
-up v
d star
oltaqe
t)
-40 -20 8085 100 120
Ambient temperature, °C
68 ds_61210_en_jjm: 010113J
.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load
