Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. side: Min.
2) For wiper load (ACQW131)
Anything outside that given below complies with standard relays. 105 (at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
Min.: 20A 14V DC, N.1 m/s2{4. Specifications
1) Standard relay
Characteristics Item Specifications
Contact
Arrangement Form C
Contact resistance (Initial) N.The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min.)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min.O. 10ms (at 200C 680F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max.Motor load does not apply wiper load applications. Also, this does not guarantee repeated switching.1 m/s2{4. 44.
ds_61208_en_cq: 310113D 53
Automotive
. operating speed cpm (at nominal switching capacity)
Mass Approx. 100 (at 500V DC, Measurement same location “Breakdown voltage” section. side: Min.5g .: Typ8mQ (By voltage drop 1A)
Contact voltage drop Max. 5x105 (Inrush 25A, steady 14V DC)
N.O.
*2. (Not freezing and condensing low temperature)
Max.O. recommend that you confirm operation under actual conditions.This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. 6.O.
*3. 10ms (at 200C 680F, excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock resistance
Functional Min.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min. 107(at 120 cpm)
Electrical*4
<Resistive load>
Min.C.H.: Typ7mQ, N. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min. Depends connection conditions. Also, this does not guarantee repeated switching. 85% R.C. recommend that you confirm operation under actual conditions.O.: 10A 14V DC
Max.5G}
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min.CQ
2. carrying current (12V initial)*1 N.C.23 oz
Notes:
*1.
*4.Depends connection conditions.
Characteristics Item Specifications
Rating Max. Refer “Usage ambient condition“ on
page 178.: 35A for minutes, 25A for hour (at 200C 68°F)
30A for minutes, 20A for hour (at 850C 1850F)
Nominal operating power 640 mW
Min. 5x105(12A 14V brake current)
(Operating frequency: ON, OFF)
Note: *1. 3x105(Inrush 30A, steady 5A, 20A 14V brake current)
(Operating frequency: ON, OFF)
Conditions
Conditions for operation, transport and storage*2
Ambient temperature: -400C +850C -400F +1850F
Humidity: R. 1mH)>
N. (Detection current: 10mA)
Operate time (at nominal voltage) Max.2V (at A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) N.H. 0. carrying current (12V initial)*3
N.: 25A for minutes, 15A for hour (at 20°C 680F)
Expected life Electrical
<Wiper motor load Approx. 44
