Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
O. Coil data
Nominal coil
voltage
Pick-up voltage
(at 200C 680F)
Drop-out voltage
(at 200C 68OF)
Nominal operating
current
[+10%] (at 200C 680F)
Coil resistance
[+10%] (at 200C 680F)
Nominal operating
power
(at 200C 680F)
Usable voltage range
(at 85°C 185°F)
12V DC
Max.H. switching capacity (resistive load)*1 12V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max. (Detection current: 10mA)
Operate time (at nominal voltage) Max.
<Resistive load> Min.C.O. recommend that you confirm operation under actual conditions. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection: 10|as)
Destructive Min. Depends connection conditions.CP
RATING
1. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load.5s OFF)
Conditions
Conditions for operation, transport and storage*2
Ambient temp: -40°C +85°C -40°F +185°F
Humidity: R. 100 (at 500V DC)
Breakdown voltage
(Initial)
Between open contacts 500 Vrms for min.: Typ6mQ, N.O. Also, this does not guarantee repeated switching.
2) For wiper load (CP1W-12V)
Anything outside that given below complies with standard relays.3 225Q 640 16V DC
Note: Other pick-up voltage types are also available. Refer “Usage ambient condition“ page 178.H. 1. 105(At nominal switching capacity, operating frequency: ON, OFF)
<Motor load*>
Min.
44 ds_61207_en_cp: 010113J
. side, Inrush 25A, steady 14V DC)
Min. 44. operating speed cpm (at rated load)
Mass Approx.1 m/s2{4. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock resistance
Functional Min. side, 20A 14V brake current) (Operating frequency: 0. . side: Min.1 m/s2{4. 107(at 120 cpm)
Electrical*4.: Typ8mQ (By voltage drop 1A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load) 20A 14V N. side, 20A 14V motor lock)
Min. 85% R.2V DC
(Initial)
Min.
*3.
2. Also, this does not guarantee repeated switching.: 40A for minutes, 30A for hour (at 20°C 68°F)
35A for minutes, 25A for hour (at 85°C 185°F)
Nominal operating power 640 mW
Min. 1mH)>
N. 105 (N. recommend that you confirm operation under actual conditions.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min. side: Min. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration resistance
Functional 100 Hz, Min. (Not freezing and condensing low temperature)
Max. carrying current (12V initial)*3
N.5G}
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min. Motor load does not apply wiper load applications.
Characteristics Item Specifications
Rating Max.O. 5x105(12A 14V brake current)
(Operating frequency: ON, OFF)
Note:*1.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F). (Detection current: 10mA)
Between contacts and coil 500 Vrms for min. 44.O. 7.
*2. 2*105 (N. Depends connection conditions.0V DC
(Initial)
53.C.
*4. 2*105 (N.O.5s ON, 9.C. Please contact for details. carrying current (12V initial) N.C.: 25A for minutes, 15A for hour (at 20°C 68°F)
Expected life Electrical
<Wiper motor load Approx.O. Specifications
1) Standard relay
Characteristics Item Specifications
Contact
Arrangement Form Form C
Initial contact resistance (Initial) N. 5x105(Inrush 25A, steady 14V DC)
N.14 oz
Notes:
*1.: 10A 14V DC
Max.: 20A 14V DC, N
