Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
295
24VAC 80%V less 30%V more 1.974 4. (Detection current: 10mA.)
Release time (at 20°C )*2
DCtype/AC type: Max.9/11.0 10,000
Notes: The rated excitation current is±10% (20°C 68°F).2 (Initial) (Initial) 23.5 10.3 1. 980 m/s2(Half-wave pulse sine wave: ms.9 650 nominal voltage nominal voltage
48V 18.4 6/6.9 2,600 (Initial) (Initial)
100/110V 1.
(This value differs depending the ambient temperature.)
Vibration resistance
Functional double amplitude (Detection time: 10|as. 35g 1.4/14.4% for every ±1°C change intemperature. applied voltage
(at 70°C 158°F)
6V 150 0. 5x105
2 Form 30V resistive load (cos9=1) Life switching cycle: Min.HL
RATING
1.
(This value differs depending the ambient temperature.)
Destructive double amplitude mm
Expected life
Mechanical type: 5x107 (at 180times/min.074
12VAC 111 100 0.7/7.), type: 108(at 180times/min. (Not freezing and condensing lowtemperature)
Max.)
Electrical
AC load 1Form 15A 125VAC, 10A 250VAC resistive load (cos^=1) Life switching cycle: Min. Thisvalue not permissible valuefor continuous operation. 100MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section.9 27. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. Thisvalue not permissiblevaluefor continuous operation.
236 61C03 hl: 080413J
. (at max. 25ms (Nominal voltage applied the coil, excluding contact bounce time.
Inparticular, forACoperation, iftheappliedvoltagedropsto80%Vormore belowthe ratedvoltage, hummingwill occurand alargecurrentwill flowleading possibly
to coil burnout. switching capacity (Reference value)*1 100mA DC
Electrical
characteristics
Insulation resistance (Initial)
Min.23 oz
Notes:
If integrating into electrical appliances that will subject compliance the Electrical Appliance and Material Safety Law, please use ambient temperature
between -50°C +40°C-58°F +104°F (ACtype).)
Between contact and coil 2,000 Vrmsfor 1min. 80°C (By resistive method, nominal voltage)
Operate time (at 20°C )*2 DCtype/AC type: Max.9 160 80%V less 10%V more 110%V of
nominal voltage
24VDC 0.)
2 ils )
Nominal coil
voltage
Nominal coil current
(mA)
Nominal operating
power (W)
Coil resistance
(Q)
Pick-up voltage
(at 20°C 68°F)
Drop-out voltage
(at 20°C 68°F)
Max.57
200/220VAC 6.
2.9 40
12V 0.7 12/13.312 0.)
Destructive Min.2 nominal voltage nominal voltage 4. Please contact usfor details.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrmsfor 1min. 5x105
2 Form 10A 250VAC resistive load (cos9=1) Life switching cycle: Min.
2.
*1This value can change due the switching frequency, environmental conditions and desired reliability level, therefore recommended checkthis with the
actual load. For use with 200V DC, connect (5W) resistor, series, the 100V relay. 3x105
DC load 1Form 30V resistive load (cos9=1) Life switching cycle: Min. continuous current. (Detection current: 10mA.
*2For the coil types, the operate/release time will differ depending the phase.
3. The coil resistance for operation isthe value measured when the coil temperature is20°C 68°F.078 0. applied
voltage
50Hz 60Hz 50Hz 60Hz When drop-out When operating
6V 224 200 0. rating)
Unit weight Approx. The maximum allowablevoltage isthe maximumvoltagefluctuation valueforthe coil power supply.5 0. Coil data
1) ils
Nominal coil
voltage
Nominal coil current
(mA)
Nominal operating power
(VA) Pick-up voltage
(at 20°C 68°F)
Drop-out voltage
(at 20°C 68°F)
Inductance (H) Max.63
110/120VAC 12.6 85.
*4 When using the socket, sure verify the max.)
2. (Detection current: 10mA. Please contact usfor details.19 25. (Byvoltage drop 1A)
Contact material AgSnO2type
Rating
Nominal switching capacity
1Form 15A 125VAC, 10A 250VAC (resistive load)
2 Form 10A 125VAC (resistive load)
Min.)
Temperature rise Max. 25ms (Nominal voltage applied the coil, excluding contact bounce time.
*3 The upper operation ambient temperature limit isthe maximumtemperature that can satisfy the coil temperature rise value. The relay operates range 80%to 110%V the voltage rating, but ideally, consideration temporary voltage fluctuations, should operated the
rated voltage.)
Between contact sets 1,500 Vrmsfor 1min.H.
5.98 81. The maximum allowablevoltage isthe maximumvoltagefluctuation value forthe coil power supply.75 20. Compensate ±0.
4.76
Notes: The relay operates range 80%to 110%V the voltage rating, but ideally, consideration temporary voltage fluctuations, should operated the
rated voltage.243 1. 5x105
Conditions
Conditions for operation, transport and storage*3
Ambient temperature: -50°C +70°C-58°F +158°F (Without LED indication);
-50°C +60°C-58°Fto +140°F (With LED indication)
Humidity: 5to 85% R.)
(without diode)
Mechanical
characteristics
Shock resistance
Functional Min. Refer “6.2/13.181
110%Vof
nominal voltage
48VAC 1. Specifications
Characteristics Item Specifications
Contact
Initial contact resistance, max Max.145
100/110VAC 13. Operating speed times/min. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626)
