Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
HJ
2. itching capacity Form type) 2-(1). continuous current.)
Release time*2
Max. 34g 1. (By voltage drop 1A)
Contact material plating type: plating Without plating type: Ag
Rating
Nominal switching capacity (resistive load) 250V 250V AC
Max. 60°C (By resistive method, nominal voltage)
Operate time*2 Max.
*2 For the coil types, the operate/release time will differ depending the phase.
REFERENCE DATA
Max. itching capacity Form type) 1-(2).)
Temperature rise (at 70°C 158°F) Max.H.
*4.)
Vibration resistance
Functional double amplitude 1. (at nominal switching capacity)
Unit weight Approx. switching power (resistive load) 1,750 1,250 VA
Max. 5x105(5A 250V AC)
Min.0 mm
Expected life
Mechanical Min. 105(7A 250V AC)
Min.When using the socket and terminal socket, sure verify the max.20 oz
Notes:
In accordance with the Electrical Appliance and Material Safety Law, you cannot exceed voltage 150V when using the Form type. switching current A
Nominal operating power 0.); therefore, please use the Au
plating type.)
Electrical (resistive load) (at times/min. (Not freezing and condensing low temperature)
Max.)
Destructive Min.
When using low level loads, contact instability may result depending conditions use (switching frequency and ambient conditions, etc. Refer Usage, transport and storage conditions
in page 229. (Detection current: 10mA. switching capacity
(Reference value)*1
Au plating type 1mA DC
Without plating type 1mA DC
Electrical
characteristics
Insulation resistance (Initial)
Min.5
_
A r
ith
es
te
is
s
tiv
b
e
ut
load
ton typ o
l
nly
r -
\
_AC istive
load
/
DC inductive load:
1 M
DC resistive loa
i i
d
N
Ac inductiv
cos 0=0 4
e lcad
50 100125 250
Contact voltage, V
10
Load current, A
ds_61C02_en_hj: 110313J 225
Power
. 105(5A 250V AC)
Min. Life curve Form C)
1
0.)
Destructive double amplitude 1. (Detection current: 10mA. Max.
*1 This value can change due the switching frequency, environmental conditions and desired reliability level, therefore recommended check this with the actual load.0 (Detection time: 10|as. switching voltage 250V AC, 125V DC
Max. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form C
Initial contact resistance, max Max.)
Between contact and coil 2,000 Vrms for 1min.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min. Operating speed times/min. 100 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. 1,000 m/s2(Half-wave pulse sine wave: ms. 20ms (Nominal voltage applied the coil, excluding contact bounce time. 100MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. 2x107(at 180 times/min.
For more information, please inquire. 2x105 (3A 250V AC)
Conditions
Conditions for operation, transport and storage*3
(Not freezing and condensing low temperature)
Ambient temperature: -40°C +70°C -40°F +158°F
Humidity: 85% R. 20ms (Nominal voltage applied the coil, excluding contact bounce time.The upper limit the ambient temperature the maximum temperature that can satisfy the coil temperature rise value.)
Min.2 VA
Min.9W 1.
*3. (Detection current: 10mA.)
(without diode)
Mechanical
characteristics
Shock resistance
Functional Min.)
Between contact sets 2,000 Vrms for 1min
