Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
)
Expected life
Electrical (resistive load) (at times/min. 90g 3. 120g 4.HE
2.17oz,
Screwterminal type: approx.82oz, Plug-in type/TM type: approx.23oz
*1 Thisvalue can change dueto the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthiswith the
actual load. rating)
Unit weight
PC board type: approx. 2x105(30A250VAC)
Min. switching power 8,310VA 6,925VA
Rating
Max.)
characteristics
Vibration resistance
Functional 10to double amplitude 1mm (Detection time: 10|as. switching capacity (Reference value)”1 100mA5V DC
Insulation resistance (Initial)
Min.
REFERENCE DATA
1 Form Type
1. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. switching current 30A 25A
Nominal operating power DC: 1. Specifications
Characteristics Item Specifications
Arrangement 1FormA FormA
Contact Initial contact resistance, max Max.)
Between contact sets 4,000 Vrms for 1min (Detection current: 10mA. m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. 980 m/s2(Half-wave pulse sine wave: ms. 107(at 180 times/min. 100 (By voltage drop 1A)
Contact material AgSnO2type
Nominal switching capacity (resistive load) 30A 277VAC 25A 277VAC
Max.)
Surge breakdown voltage”2
(between contact and coil)
Min. 105(30A 277VAC)
Min.
Breakdown voltage
(Initial)
Between open contacts 2,000 Vrms for 1min (Detection current: 10mA. 5x106(at 180 times/min.92W, AC: 1.)
Destructive 10to double amplitude 1. Refer “6.), AC: Min.7to 2.2x50p,s according JEC-212-1981
*3 The upper limit ofthe ambient temperature isthe maximumtemperature that can satisfy the coil temperature rise value. 2x105(20A 250VAC)
Conditions
Conditions for operation, transport and storage*3
Ambient temperature: -500C +550C-580F +1310F
Humidity: 5to 85% R. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626).)
Min. (Not freezing and condensing lowtemperature),
Air pressure: 106kPa
Conditions for operation, transport and storage*3 20times/min. 105(25A 277V AC)
Min. axim switching power Life curve
Contactcurrent,A
3.)
Mechanical Destructive Min. Coil tem perature rise (DC type)
Measured portion: Inside the coil
Contact current: A
ds 61C06 he: 150313D 211
Power
.7VA
Min.
*2 Wave standard shock voltage ±1.)
Electrical
characteristics
Between contact and coil 5,000 Vrms for 1min (Detection current: 10mA.5 mm
Mechanical DC: Min.10ms (excluding contact bounce time, without diode),
AC: Max. 30ms (excluding contact bounce time)
Shock resistance
Functional Min. (at max.H. 65°C (at 55°C) (By resistive method)
Operate time (at nominal voltage) Max. 600C (at 55°C) (By resistive method), AC: Max. switching voltage 277VAC, 30V DC
Max. 80g 2. 10,000V (initial)
Temperature rise DC: Max. 30ms (excluding contact bounce time)
Release time (at nominal voltage) DC: Max
