Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
5A Min. 2x105
resistive load
(at times/min. 2x105
5A 2.H.06 oz
Notes:
*1. 105
resistive load
(at times/min.4A Min. switching capacity
(Reference value)*1
1mA 100pA DC
Electrical
characteristics
Insulation resistance (Initial) Min.HC
2 ific tio s
Characteristics Item Specifications
Contact
Arrangement Form Form Form Form Form (twin)
Contact resistance (Initial) Max.)
Between contact
sets
700 Vrms for 1min.5A Min. 106
4 Form (twin) 0. (Detection current: 10mA. 106
2 Form C
7A 3. switching current*4 10A 3A
Nominal operating power (50Hz): 1. continuous current.5A 0. (Not freezing and condensing low temperature)
Max.5A Min. 1,000MQ (at 500V DC) Measurement same location “Breakdown voltage” section. This value can change due the switching frequency, environmental conditions and desired reliability level, therefore recommended check this with the actual load.
3 itc ity life
(1 tric tim .5A Min. 5x105
5A 1. 106
3 Form C
7A Min.4A Min.5A Min. 108: coil type (at 180 times/min. 2x105
resistive load
(at times/min.)
Destructive Min.)
Destructive double amplitude mm
Expected life
Mechanical Min.)
Min.)
Conditions
Conditions for operation,
transport and storage*3
Ambient temperature: -50°C +70°C -58°F +158° (without LED); -50°C +60°C 58°F +140°F (with LED)
Humidity: 85% R. 2x105
5A 0. 980 m/s2 (Half-wave pulse sine wave: ms.
*2.)
Electrical
Min.) (without diode)
Mechanical
characteristics
Shock
resistance
Functional Min. Refer Usage, transport and storage conditions
in NOTES page 200.3VA, (60Hz): 1. (at max. 30g 1. 5x105
4 Form C
5A Min. For the coil types, the operate/release time will differ depending the phase.)
Temperature rise (coil)
(at 700C 158°F)
Max. 5x105
3A 1. When using the socket and terminal socket, sure verify the max.9 1. 20ms (Nominal coil voltage applied the coil, excluding contact bounce time. 5x107: coil type (at 180 times/min. (Detection current: 10mA.)
Min.6A Min. 2x105
3A 0. 8
ds 61C04 hc: 110313J 193
Power
. (By voltage drop 1A)
Contact material alloy (cd free) flash AgNi type clad
Rating
Nominal switching capacity
(resistive load)
10A 250V 250V 250V 250V 250V AC
Max. 80°C 176°F (By resistive method, nominal coil voltage)
Operate time (at 20°C 68°F)*2 Max.); Min. 2x105
(2 tim .1W
Min. switching power
(resistive load)
2,500VA 1,750VA 1,750VA 1,250VA 750VA
Max. 2x105
7A 2.)
Load
AC DC
Expected lifeResistive (cos Inductive (cos 0. 2x105
resistive load
(at times/min.8A 0.)
Release time (at 20°C 68°F)*2 Max.
Breakdown
voltage
(Initial)
Between open
contacts
700 Vrms for 1min. 105
— 3.)
Min.5A 0. (Detection current: 10mA. rating)
Unit weight Approx.)
Vibration
resistance
Functional double amplitude (Detection time: 10|as. Operating speed times/min.5A 1. The upper limit the ambient temperature the maximum temperature that can satisfy the coil temperature rise value.
*3. 20ms (Nominal coil voltage applied the coil, excluding contact bounce time.2VA, DC: 0.
*4.)
A in.4) Resistive Inductive
Voltage 125V 250V 125V 250V 30V 30V DC
1 Form C
10A 10A Min.)
Between contact
and coil
2,000 Vrms for 1min.)
Min.8A Min.4A Min. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. 5x105
2A 0. switching voltage 250VAC
Max. 2x105
resistive load
(at times/min