Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
(Detection current: mA)
Surge breakdown voltage (Initial)”2 6,000 (Between contact and coil)
Operate time [Set time] (at 20°C 68°F)
Max.)
Mechanical
characteristics
Shock resistance
Functional Min. 105(8A 250 VAC resistive) (ON :OFF s)
Conditions
Conditions for operation, transport and storage”3
Ambient temperature: -40°C +60°C-40°F +140°F;
Humidity: 85% R. mQ(By voltage drop 1A)
Rating
Max.
REFERENCE DATA
1. operating speed times/min. 55°C
(By resistive method, nominal voltage applied the coil; contact carrying current: 8A. [Max. Specifications
Characteristics Item Specifications
Contact
Arrangement 1FormA 1Form FormA
Contact material Au-flashed AgSnO2type
Initial contact resistance, max.)
Destructive Min.H. ms]
(Nominal voltage applied the coil, excluding contact bounce time.)
Vibration resistance
Functional 10to double amplitude (Detection time: 10ps.)
Electrical Min. 107(at 180times/min. (Detection current: mA)
Between contact sets 2,000 Vrms for 1min. Max. Usage, Storage and Transport Conditions” inAMBIENT ENVIRONMENT (page 626). switching power (resistive load) 3,040 VA, 150 W
Max. (Detection current: mA)
Between contact and coil 3,750 Vrms for 1min. Max.)
Release time [Reset time] (at 20°C 68°F)
Max. [Max. ms]
(Nominal voltage applied the coil, excluding contact bounce time. switching capacity (Reference value)*1 100 mA5V DC
Electrical
characteristics
Insulation resistance (Initial)
(at 25°C, 50% relative humidity)
Min.353 oz
*1 This value can change dueto the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load. 980 m/s2(Half-wave pulse sine wave: ms.
*3 Refer “6.2x50p,s according JEC-212-1981.*4
Unit weight Approx. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section.
*4 The max. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10ps. switching current 8A
Minimum operating power 150mW(Single side stable, coil latching)
Nominal operating power 240mW(Single side stable, coil latching)
Min. switching voltage 380 AC, 250 DC
Max. itching power Coil tem perature rise Influence adjacent ounting
-Voltage,V
op-outvo
- _
Pic
- \
k-upvol age
10 20
^inter-relaydistance, mm
ds 61A09 st: 070313D 181
PolarizedPower
.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min.) (without diode)
Temperature rise (at 60°C 140°F)
Max. operating speed amounts 30cps without load.
*2 Wave standard shock voltage ±1. 10g .
Breakdown voltage
(Initial)
Between open contacts 1,200 Vrms for 1min.ST
2. (Not freezing and condensing lowtemperature)
Max
