Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
105(10 [at times/min.
*2 Referto “6.]), Min.)
Electrical (resistive load)
2 Form C:
Min. (at rated load)
Unit weight Form 1.])
4 Form C:
Min.])
Conditions
Conditions for operation, transport and storage”2 Ambient temperature: -50°C +60°C-58°F +140°F;
Humidity: 85% R. Specifications
Characteristics Item Specifications
Contact
Initial contact pressure Form Approx. operating speed times/min. 5x107(at 180times/min. switching capacity (Reference value)”1 100 DC
Electrical
characteristics
Insulation resistance (Initial)
(25°C, 50% relative humidity)
Min. ms]
(Nominal voltage applied the coil, excluding contact bounce time.)
Vibration resistance
Functional 10to double amplitude (Detection time: 10|as. switching power (resistive load) Form 3,750 VA, 300 Form 2,500 VA, 300 W
Max. 2A)
Max.SP
2. [Max. 105(10 [at times/min. 0.
REFERENCE DATA
O perate and release tim (Single side stable)
SP2 SP4
C oil tem perature rise
Tested sample: SP2-DC24V
Ambient temperature: 22°C 72°F
174 ds_61A08_en_sp: 030413D
.392 N(40 1.)
Mechanical
characteristics
Shock resistance
Functional Min.71 oz)
Arrangement Form Form C
Initial contact resistance, max.196 N(20 0. [Max. 40°C
(By resistive method, nominal voltage applied the coil; nominal switching capacity.76 oz;4 Form 2.)
Destructive Min. 980 m/s2(Half-wave pulse sine wave: ms. (Not freezing and condensing lowtemperature)
Max. 0.) (without diode)
Temperature rise (at 20°C 68°F) Max. switching voltage Form Form 250 VAC, (48V DC: Max.]), Min.H. 105(15A 250 VAC [at times/min. 392 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as.
Breakdown voltage
(Initial)
Between open contacts 1,500 Vrms for 1min.29 oz
*1 Thisvaluecanchange duetotheswitchingfrequency, environmental conditions, and desired reliability level, therefore isrecommended tocheckthiswith theactual load. switching current Form 15A (AC) 10A (DC), Form A
Minimum operating power 150mW(Single side stable, coil latching)
Nominal operating power 300mW(Single side stable, coil latching)
Min. (Detection current: mA)
Between contact sets 3,000 Vrms for 1min. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. 105(15A 250 VAC [at times/min.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min. (Detection current: mA)
Between contact and coil 3,000 Vrms for 1min. (Detection current: mA)
Operate time [Set time] (at 20°C 68°F) Max.41 oz), Form Approx. (By voltage drop 1A)
Contact material Stationary contact: flashed AgSnO2type, Movable contact: AgSnO2type
Rating
Nominal switching capacity (resistive load) Form 250 AC, Form 250 AC
Max.)
Release time [Reset time] (at 20°C 68°F) Max. ms]
(Nominal voltage applied the coil, excluding contact bounce time. Usage, Storage and Transport Conditions” inAMBIENT ENVIRONMENT (page 626). Max