Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
(Detection current: 10mA.)
(without diode)
Mechanical
characteristics
Shock resistance
Functional Min.)
Electrical Min.)
Release time [Reset time] (at 20°C 68°F) Max.-(1) Life curve Form Form 2. operating speed cps
Unit weight Approx. switching current AAC, AC, DC
Nominal operating power Single side stable, coil latching: 300 mW.16 oz
Notes:
*1 Thisvalue can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the
actual load. itching capacity 2. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as.)
Vibration resistance
Functional 10to double amplitude (Detection time: 10|as. 105 (resistive load)
Conditions
Conditions for operation, transport and storage*3
(Not freezing and condensing lowtemperature)
Ambient temperature:
-400Cto +600C
-40°Fto +1400F
Ambient temperature:
-40°C +65°C
-40°Fto +149°F
Ambient temperature:
-40°C +60°C
-40°Fto +140°F
Solder heating
2500C 482°F (10s), 300°C 572°F (5s), 350°C 662°F (3s)
(Soldering depth: 2/3 terminal pitch)
Max. [10 ms] (Nominal voltage applied the coil, excluding contact bounce time. Specifications
Characteristics Item Specifications
Contact
Arrangement 1FormA 1Form 1Form FormA
Initial contact resistance, max. [10 ms] (Nominal voltage applied the coil, excluding contact bounce time.)
Destructive 10to double amplitude 3.2x50p,s according JEC-212-1981
*3 Referto “6.-(2) Life curve Form Form B)
Switching capacity, Switching capacity, A
152 ds_61A05_en_dsp: 070313D
. switching voltage 250 AC, 125V DC
Max. switching capacity (Reference value)*1 10mA DC
Electrical
characteristics
Insulation resistance (Initial)
Min. Max. Max.DSP
2. mQ(By voltage drop 1A)
Contact material Au-flashed AgSnO2type
Rating
Nominal switching capacity (resistive load) 250 VAC, 30V 250 AC, DC
Max.5 . (Detection current: 10mA.)
Between contact and coil 3,000 Vrms for 1min. 5x107 (at 180times/min. 55°C
Operate time [Set time] (at 20°C 68°F) Max. 1coil latching: 150mW
Min. switching power (resistive load) 2,000 VA, 150W 1,250 VA, 150 W
Max.
*2 Wave standard shock voltage ±1.)
Between contact sets 2,000 Vrms FormA 1Form FormA) (Detection current: 10mA.)
Destructive Min. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. 4. Usage, Storage and Transport Conditions” inAMBIENT ENVIRONMENT (page 626). 980 m/s2(Half-wave pulse sine wave: ms.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min.5 mm
Expected life
Mechanical Min. 40°C Max.
REFERENCE DATA
1.)
Surge breakdown
voltage*2
between contacts and coil 5,000 V
Temperature rise (at 65°C 149°F) Max. 55°C Max
