Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
)
Vibration resistance
Functional 10to double amplitude (Detection time: 10|as.2x50p,s according JEC-212-1981
*3. 200 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. Wave standard shock voltage ±1.
130 ds_61A02_en_dj: 120711J
.
*2. 105 (at 10A250VAc): Form FormA, Form 1FormA 1Form B
Conditions Conditions for operation, transport and storage*4
Ambient temperature: -40°C +70°C
Humidity: 85% R.H.)
Between contact and coil 4,000 Vrms for 1min. 1,000MQ (at 500V DC) Measurement same location “Breakdown voltage” section.)
Surge breakdown
voltage*2(Initial)
Between contact and coil Min. switching current
16A Form 1Form Form B),
10A FormA Form Form FormA, Form B)
Nominal operating power 150mW(1 coil latching), 250mW(Single side stable, coil latching)
Min. 1,000 m/s2(Half-wave pulse sine wave: ms. 5x106(at 180times/min. 105 (at 16A250VAC): 1Form 1FormA, 1Form B
Min.)
Mechanical
characteristics
Shock resistance
Functional Min.)
Min. Specifications
Characteristics Item Specifications
Contact
Arrangement 1Form FormA, Form 1FormA 1Form Form FormA, Form B
Contact resistance (Initial) Max.(ADJ)
RATING
1. switching voltage 250VAC
Max.49 oz
Notes:
*1. orderto obtain the full rated lifecycles, the relay should properly vented removing the vent nib. [20 ms] (Nominal voltage applied the coil, excluding contact bounce time. Refer “6.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min. switching capacity (Reference value)*1 100mA5V DC
Electrical
characteristics
Insulation resistance (Initial) Min. 55°C (By resistive method, nominal voltage applied tothe coil, max. applied voltage
(at 200C680F)
5V 100Q
6V DC
70%Vor less nominal
voltage (Initial)
70%V less nominal
voltage (Initial)
144Q
12V 576Q 250mW 130%Vof nominal voltage
24V 2,304Q
48V 9,216Q
2.)
Operate time [Set time] (at 20°C 68°F) Max. (Not freezing and condensing lowtemperature)
Unit weight Approx. (Detection current: 10mA. 10,000 V
Temperature rise (coil) (at 700C 158°F) Max.
*4. switching power (resistive load) 4,000 VA
Max. switching current. Thisvaluecanchange duetotheswitchingfrequency, environmental conditions, and desired reliability level, therefore isrecommended tocheckthiswith theactual load.)
Electrical (Resistive load)*3(at times/min. [20 ms] (Nominal voltage applied the coil, excluding contact bounce time. applied voltage
(at 200C680F)
5V DC
70%Vor less nominal
voltage (Initial)
70%Vor less nominal
voltage (Initial)
167Q
150mW 130%Vof nominal voltage
6V 240Q
12V 960Q
24V 3,840Q
48V 15,360Q
3) coil latching
Nominal coil voltage
Set voltage
(at 200C 680F)
Reset voltage
(at 200C 680F)
Coil resistance
[+10%] (at 200C680F)
Nominal operating power
Max.)
Destructive Min. applied voltage
(at 200C680F)
5V DC
75%Vor less nominal
voltage (Initial)
10%Vor more nominal
voltage (Initial)
100Q
250mW 130%Vof nominal voltage
6V 144Q
12V 576Q
24V 2,304Q
48V 9,216Q
2 coil latching
Nominal coil voltage
Set voltage
(at 200C 680F)
Reset voltage
(at 200C 680F)
Coil resistance
[+10%] (at 200C 680F)
Nominal operating power
Max. The upper limit the ambient temperature isthe maximum temperature that can satisfy the coil temperature rise value.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min. 100 (Byvoltage drop 1A)
Contact material
AgSnO2type Form 1Form Form B),
Au-flashed AgSnO2type FormA 1Form Form FormA, Form B)
Rating
Nominal switching capacity (resistive load)
16A 250V Form 1FormA, 1Form B),
10A 250V Form FormA, Form FormA Form B)
Max. For more details, please look caution for NOTES page 135. (Detection current: 10mA. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626). . Coil data
1) Single side stable
Nominal coil voltage
Pick-up voltage
(at 200C 680F)
Drop-out voltage
(at 200C 680F)
Coil resistance
[+10%] (at 200C680F) Nominal operating power
Max.)
Release time [Reset time] (at 20°C 68°F) Max
