Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
(Not freezing and condensing lowtemperature)
Max.2mA 4050 4050
12V 16.6mA 11., nominal
switching capacity)
Min. 4ms)
(Nominal coil voltage applied the coil, excluding contact bounce time.H. Specifications
Characteristics Item Specifications
Arrangement 1FormA 1FormA 1Form FormA
Contact Contact resistance (Initial) Max. (typ. 105
(resistive load, times/min. (typ. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626).3mA 33.6mA 66.
124 61A01 de: 150313D
.)
Mechanical Destructive Min. (at nominal switching capacity)
Unit weight Approx.)
Release time [Reset time] (at 20°C 68°F)
Max. 105 (resistive load,
at 20times/min. (Detection current: mA)
Between contact and coil 5,000 Vrms for 1min. (Detection current: mA)
Between contact sets 4,000 Vrms for min. switching power (resistive load) 2,500VA*4,300W 2,000VA*4,240W
Rating
Max. (typ. (By voltage drop 1A)
Contact material AgSnO2type
Nominal switching capacity (resistive load) 10A250VAC, 10A30V 250V AC, 30V DC
Max.5V DC
70%Vor less of
nominal voltage
(Initial)
70%V less of
nominal voltage
(Initial)
66., nominal switching capacity)
Min.
*4. 2ms)
Max. switching capacity*1 100mA5V DC
Insulation resistance (Initial) Min.2x50p,s according JEC-212-1981
*3.)
characteristics
Vibration resistance
Functional double amplitude (Detection time: 10|as. 16A possible for one cantact set only with max. (typ. Refer “6. 4000VA switching power. The upper limit the ambient temperature isthe maximumtemperature that can satisfy the coil temperature rise value.5mA 1010 101 0
5V 40mA 40mA 1250 1250
6V 33., nominal
switching capacity)
Electrical (16A/230VAC resistive)*4 25000 2000
Conditions
Conditions for operation, transport and storage*3
Ambient temperature: -40°C +70°C -40°Fto +158°F;
Humidity: 5to 85% R.6mA 16. Wave standard shockvoltage ±1.)
Expected life Electrical
Min. 4ms)
(Nominal coil voltage applied the coil, excluding contact bounce time. 50°C 122°F (By resistive method)
Operate time [Set time] (at 20°C 68°F)
Max. applied voltage
(at 200C 68OF)
Set coil Reset coil Set coil Reset coil Set coil Reset coil
1.3mA 2,8800 2,8800
2.6mA 45Q 450
4. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as.25 oz
Notes:
*1.)
Destructive double amplitude mm
Mechanical Min. switching current 10A (16A)*4 (16A)*4
Nominal operating power Single side stable, coil latching: 200mW; 1coil latching: 100mW
Min.30 11. operating speed times/min. 1,000MO (at 500V DC) Measurement same location “Breakdown voltage” section.6mA 7200 7200
24V 8.3mA 8.30
200mW 200mW
130%V of
nominal voltage
3V 66. switching voltage 440VAC, 230V 440VAC, 230V DC
Max. 5ms)
Max.5V 44. 5x104 (resistive load,
at 20times/min. 980 m/s2(Half-wave pulse sine wave: ms. 107 (at 300 times/min.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min.5mA 44.(ADE)
3) coil latching type
Nominal coil
voltage
Set voltage
(at 200C68°F)
Reset voltage
(at 200C 68OF)
Nominal operating
current
[±10%] (at 20°C 68°F)
Coil resistance
[±10%] (at 20°C 68°F)
Nominal operating
power Max. (Detection current: mA)
Electrical
Surge breakdown voltage*2
(Between contact and coil) (Initial) 12,000 V
characteristics Temperature rise (coil) (at 70°C 158°F) Max.) (without diode)
Shock resistance
Functional Min. .
*2.2mA 22.3mA 1800 1800
9V 22. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load.6mA 66
