Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Poznámky redaktora
000 Vrmsfor 1min.B.) Min. (Detection current: 10mA)
2,000 Vrms for 1min.071 oz
*1 M.)
Conditions
Conditions for operation, transport and
storage”3
Ambient temperature: -400C +850C-400F +1850F;
Humidity: 5to 85% R.]. (Detection current: 10mA)
voltage (Initial)
Between contact and coil
Surge breakdown voltage 2,500 type:
2. 100 (By voltage drop 1A)
Contact material
Standard contact: Ag+Au clad,
AgPd contact (low level load): AgPd+Au clad (stationary), AgPd (movable)
Nominal switching capacity
Standard contact: DC,
AgPd contact: (resistive load)
1A 30V (resistive load)
Max.2 50^s
2,500 10|as (Telcordia)
Temperature rise (at 200C 68°F)
Max.)
*3 The upper operation ambient temperature limit isthe maximumtemperature that can satisfy the coil temperature rise value. (Detection current: 10mA)
Surge breakdown voltage
6,000 (High breakdown voltage) type:
1,500 Vrmsfor 1min. type models are only available 2,500 surge breakdown voltage type. 107(at 180 times/min. switching current Standard contact: 2A, AgPd contact: 1A
Min. (Detection current: 10mA)
Electrical Between contact sets 1,000Vrms for 1min. [Max.H. switching capacity (Reference value)*2 10|aA10mV DC
Rating
Nominaloperating
Single side stable
Surge breakdown voltage
2,500 and 6,000 types:
200mW(1. operating speed (at rated load) times/min. 108(at 180times/min.
*2 This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load. 105(2 resistive),
Min.)
Operate time [Set time] (at 200C680F) Max.3 (Detection time: 10|as.type)"1
Contact
Contact resistance (Initial) Max. Usage, Storage and Transport
Conditions” inAMBIENT ENVIRONMENT (page 626). (Detection current: 10mA)
Surge breakdown voltage 6,000 and
6,000 (High breakdown voltage) types:
3.)
Release time [Reset time] (at 200C680F) Max. 750 m/s2
(Half-wave pulse sine wave: ms;
detection time: 10|as. .5to DC), 270mW(24V DC)
power
1coil latching
Surge breakdown voltage
2,500 and 6,000 types:
150mW(1.B.5to 12V DC), 310mW(24V DC)
250mW(1. (Not freezing and condensing lowtemperature)
Max. 1,000MQ (at 500V DC) Measurement same location “Initial breakdown voltage” section.)
Expected life
Electrical Min.5to 12V DC), 170mW(24V DC)
Surge breakdown voltage
6,000 (High breakdown voltage) type:
230mW(1. ms] (Nominal coil voltage applied the coil, excluding contact bounce time. [Max. 1,000 m/s2{100G} (Half-wave pulse sine wave: ms. switching voltage 220 110V DC
Max. Referto “6.5to 12V DC), 230mW(24V DC)
Surge breakdown voltage
6,000 (High breakdown voltage) type:
280mW(1.5to 12V DC), 250mW(24V DC)
—
Insulation resistance (Initial) Min.)
Destructive Min.
Between open contacts
Surge breakdown voltage
2,500 and 6,000 types:
1,000 Vrmsfor 1min. (Detection current: 10mA)
characteristics Between open contacts 1,500 (10x160|as) (FCC Part 68) —
Surge breakdown
voltage (Initial) Between contacts and
coil*1
Surge breakdown voltage 2,500 type:
2,500 10|as (Telcordia)
Surge breakdown voltage 6,000 and 6,000 V
(High breakdown voltage) types:
6,000 1.B.000 Vrmsfor 1min.)
(without diode)
Mechanical
characteristics
Shock
resistance
Functional
Min. (AgPd contact type available for low level load switching.B.) Min.)
Vibration Functional double amplitude 3.B. 500 m/s2
(Half-wave pulse sine wave: ms;
detection time: 10|as.
Unit weight Approx.TX-D
2. Specifications
Characteristics Item Specifications
Arrangement Form Form D(M. (Detection current: 10mA)
500 Vrms for 1min. ms] (Nominal coil voltage applied the coil, excluding contact bounce time. 500C 1220F
(By resistive method, nominal coil voltage applied the coil;
contact carrying current: [1A: M.
102 61022 txd: 150113D
.)
resistance Destructive 10to double amplitude mm
Mechanical Min.B. switching power Standard contact: 60W (DC),
AgPd contact: (DC) (resistive load)
30 (DC) (resistive load)
Max. 105(1 30V resistive) (at times/min.)
Min. 5x1Q5(1A30VDCresistive) (at 20times/min
