|
Kategorie: Katalog |
Tento dokument chci!
Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Strana 294 z 1090
«
Vámi hledaný text obsahuje tato stránku dokumentu který není autorem určen k veřejnému šíření.
»
Jak získat tento dokument?
Poznámky redaktora
level].)
Conditions
Conditions for operation, transport and storage2”
Ambient temperature: -400C +850C (up coil) -400Fto +1850F (up coil)
[-400Cto +700C (48 coil) -400Fto +1580F (48 ];
Humidity: 85% R. [Max.)
Vibration resistance
Functional 10to double amplitude 3.)
Electrical Min. switching voltage 220V DC
Max. ms] (Nominal coil voltage applied the coil, excluding contact bounce
time. operations, X104
92 61022 tx: 060213D
. (Detection current: 10mA)
Between contact and coil 2,000 Vrms for 1min.H.
Min.3 (Detection time: 10|as.5 DC)
2 coil latching 200 mW(1. switching capacity (Reference value)1” 10pA 10mV DC
Nominal operating
power
Single side stable 140 mW(1.)
Destructive Min.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min. 500C
(By resistive method, nominal coil voltage applied the coil; contact carrying current: 2A. 108(at 180times/min.)
2* Refer “6. 100 mQ(By voltage drop 1A)
Contact material
Standard contact: Ag+Au clad,
AgPd contact (low level load): AgPd+Au clad (stationary), AgPd (movable)
Rating
Nominal switching capacity Standard contact: DC, AgPd contact: (resistive load)
Max. 105(2 resistive), 5x105(1 resistive) (at times/min.
Operating speed: 180times/min.5 DC), 270 mW(48V DC)
1coil latching 100 mW(1. operating speed (at rated load) times/min.
Unit weight Approx.)
Operate time [Set time] (at 200C680F)
Max.
Min. Specifications
Characteristics Item Specifications
Contact
Arrangement Form C
Initial contact resistance, max. . switching current Standard contact: AgPd contact: 1A
Min.)
Release time [Reset time] (at 200C680F) Max. (Detection current: 10mA)
Surge breakdown
voltage (Initial)
Between open contacts 1,500 (10x160|as) (FCC Part 68)
Between contacts and coil 2,500 (2x10|as) (Telcordia)
Temperature rise (at 200C 68°F)
Max. (Not freezing and condensing lowtemperature)
Max.
REFERENCE DATA
1.) (without diode)
Mechanical
characteristics
Shock resistance
Functional Min.071 oz
1* This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual
load. [Max. Max. 1,000 m/s2(Half-wave pulse sine wave: ms.5 DC)
Electrical
characteristics
Insulation resistance (Initial)
Min. ms] (Nominal coil voltage applied the coil, excluding contact bounce
time. (Detection current: 10mA)
Between contact sets 1,000 Vrms for 1min. Usage, Storage and Transport Conditions” inAMBIENT ENVIRONMENT (page 626). axim itching capacity Life curve echanical life
Tested sample: TX2-5V, pcs. 750 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as. switching power Standard contact: (DC), AgPd contact: (DC) (resistive load)
Max.TX
2.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min.
> 100
<d 90
O)
I 80
1 70
“ 60
(D
r 50
U)
I 40
en
o 30
20
10
0
ca
pvoltage
p-out voltage
Max.
Max.
10 100 1,000 10,000
No. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. (AgPd contact type available for low level load switching [10V DC, 10mA max
