|
Kategorie: Katalog |
Tento dokument chci!
Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Strana 285 z 1090
«
Vámi hledaný text obsahuje tato stránku dokumentu který není autorem určen k veřejnému šíření.
»
Jak získat tento dokument?
Poznámky redaktora
ms] (Nominal coil voltage applied the coil, excluding contact bounce
time. 750 m/s2(Half-wave pulse sine wave: ms; detection time: 10ps. level])
*2 Refer “6.)
Vibration resistance
Functional 10to double amplitude 3. mQ(By voltage drop 1A)
Contact material AgNi type+Au clad
Rating
Nominal switching capacity DC, 0. (TX/TX-S/TX-D relay AgPd contact types are available for low level load switching [10V DC, 10mA max. (Not freezing and condensing lowtemperature)
Max. 108(at 180times/min. . [Max. Specifications
Characteristics Item Specifications
Contact
Arrangement Form C
Initial contact resistance, max. 50°C
(By resistive method, nominal coil voltage applied the coil; contact carrying current: 2A.)
Destructive Min. switching capacity (Reference value)”1 10pA 10mV DC
Nominal operating
power
Single side stable 140 mW(1.5 DC), 200 mW(24V DC), 300 mW(48 DC)
1coil latching mW(1.071 oz
Notes:
*1 This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load. Usage, Storage and Transport Conditions” AMBIENT ENVIRONMENT (page 626).
Unit weight Approx. -40°C +70°C (2A) Max. switching power (DC), 62. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section.)
Release time [Reset time] (at 20°C 68°F) Max. switching current 2A
Min.TQ
2. 2x105(1 resistive),
Min. (Detection current: mA)
Surge breakdown
voltage (Initial)
Between open contacts 1,500 (10x160ps) (FCC Part 68)
Between contacts and coil 2,500 (2x10ps) (Bellcore)
Temperature rise (at 20°C 68°F)
Max. 1,000 m/s2(Half-wave pulse sine wave: ms. 105(0. -40°F +158°F (2A);
Humidity: 85% R.5 DC), 200 mW(24V DC)
Electrical
characteristics
Insulation resistance (Initial) Min.)
Electrical
Min.5 125VAC (resistive load)
Max.
Breakdown voltage
(Initial)
Between open contacts 1,000 Vrms for 1min.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min. switching voltage 220 DC, 125V AC
Max.5to 12V DC), 100 mW(24V DC)
2 coil latching 140 mW(1. (Detection current: mA)
Between contact sets 1,500 Vrms for 1min. Max. 105(2 resistive), Min.5 125VAC resistive) (at 20times/min.)
Conditions
Conditions for operation, transport and storage*2
Ambient temperature:
-40°C +85°C-40°Fto +185°F,Max. ms] (Nominal coil voltage applied the coil, excluding contact bounce
time.H.) (without diode)
Mechanical
characteristics
Shock resistance
Functional Min. operating speed (at rated load) times/min.5 (AC) (resistive load)
Max.
ds_61020_en_tq: 060213J 83
Signal
. (Detection current: mA)
Between contact and coil 1,500 Vrms for 1min.)
Operate time [Set time] (at 20°C 68°F) Max. [Max.3 (Detection time: 10ps
