Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Also, this does not guarantee repeated switching.(ACJ)
RATING
1. Coil data
Nominal coil
voltage
Pick-up voltage
(at 20oC 680F)
Drop-out voltage
(at 20oC 68°F)
Nominal operating
current
[+10%] (at 20oC 68oF)
Coil resistance
[+10%] (at 200C 68oF)
Nominal operating
power
(at 20oC 68oF)
Usable voltage range*
12 DC
Max.: 10A 14V DC
Max. 6.5s OFF)
[Pin Paste type]
<Resistive load>
Min.C.C.5G} (Detection time: 10|as)
Destructive
10 500 Hz, Min.8 DC
(Initial)
66. side: Min.23 oz
Notes:
*1. Refer “Usage ambient condition“ on
page 178.: for hour, for minutes (at 20°C 68°F) (when coil powered one side)
Nominal operating power 640 (for pick-up voltage max.5s ON, 9. 100 m/s2{10G} (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. 105: (brake) (Operating frequency: 0.: Typ7mQ, N. 44.12 oz, Twin type: approx.H. 7. 107(at 120 cpm)
Electrical
[Standard type]
<Resistive load>
Min.
* the relay used continuously for long periods time with coils both sides energized condition, breakdown might occur due abnormal heating depending on
the carrying condition. carrying current (14V DC) N.
Please inquire you will using the relay high temperature atmosphere (110°C 230°F).: Typ10mQ (By voltage drop A)
Contact material alloy (Cadmium free)
Protective construction
Standard type: Sealed type
Pin Paste type: Flux tight type
Rating
Nominal switching capacity (resistive load) N. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min.1m/s2{4. (Not freezing and condensing low temperature)
Max. 105(at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
N.5 DC
(Initial)
Min. 85% R. 5x104: (Motor lock)
N.: 20A 14V DC, N.5 .H. 105(at nominal switching capacity, operating frequency: ON, OFF)
<Motor load>
N.
*3.5s ON, 9. 6. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form Cx2
Contact resistance (Initial) N. 105: (inrush), (steady), DC; Min.5G}
Time vibration for each direction; direction: hours, direction: hours
Expected life
Mechanical Min. Please contact for details.O.O.O. 2x105: (brake) (Operating frequency: 0. Therefore, please inquire when using with circuit that causes energized condition both sides simultaneously.
2. (Detection current: 10mA)
Operate time (at nominal voltage) Max. 1. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Initial insulation resistance Min. 3. 105: (Motor lock)
N.1m/s2{4.7 180Q 800 DC
* Other usable voltage range types are also available.5 DC)
Min. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration
resistance
Functional 100 Hz, Min.O.5 . operating speed cpm (at nominal switching capacity)
Mass Form type: approx. side: Min. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Release time (at nominal voltage) Max.3 225Q 640 DC
Max.C. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load.
ds_61215_en_cj: 010113D 27
Automotive
. 44. side: Min. side: Min.5s OFF)
Conditions
Conditions for operation, transport and
storage*2
Ambient temperature: -40°C +85°C -40°F +185°F
Humidity: R. The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value. 10ms (at 20°C 68°F, excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock
resistance
Functional Min.)
Breakdown
voltage (Initial)
Between open contacts 500 Vrms for min.2 DC), 800 (for pick-up voltage max.O.0 DC
(Initial)
53. 100 (at 500V DC, Measurement same location “Breakdown voltage” section.2 DC
(Initial)
Min. Depends connection conditions. 6. 7. 2x105: (inrush), (steady), DC; Min. recommend that you confirm operation under actual conditions.C.
*2. 0