Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
197
10
.)
Temperature rise
Max.
(500Vrms for 1min: Form high sensitivity type) (Detection current: 10mA.
Operating speed: times/min. 650C
(By resistive method, nominal coil voltage applied the coil, contact carrying current: 2A. Influence adjacent ounting
(2 Form C)
Pick-up voltage (1) (2) (3)
*5»' EMHäHj-
ON ON
ÍM-•UHíh-
Drop-out voltage
ON ON
EM-*UMíh-
y 5
. 108(107: 1Form latching type) (at 600 times/min. Usage, Storage and Transport Conditions” inAMBIENT ENVIRONMENT (page 626).394
-Inter-relay distance inch
5-(2).
REFERENCE DATA
1.394
-Inter-relay distance inch
58 61005 ds: 310513J
.. 490 m/s2
Destructive Min.
Unit weight Approx. . Detection level: 200 mQ
- Switching current Switching current, No. operating speed (at rated load) times/min. Influence adjacent ounting
(1 Form C)
.
Breakdown voltage
(Initial)
Between open contacts
1,000 Vrms for 1min. axim switching capacity Life curve (Resistive load) ontact reliability for loads
Tested sample: DS2E-S-DC24V pcs. (Not freezing and condensing lowtemperature)
Max.)
Conditions
Conditions for operation, transport and storage”3 Ambient temperature: -400C +700C 400Fto +1580F
Humidity: 5to 85% R.DS
2. switching capacity (Reference value)”1 10pA 10mV DC
Nominal operating power Single side stable (Stype: 200 mW); latching (Stype: 180 mW)
Electrical
characteristics
Insulation resistance (Initial)
Min. operations, [|104
4. 490 m/s2 Min.14oz
1* This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load. 100MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section. switching power 125VA (resistive load)
Max.)
Operate time [Set time] (at 200C 68°F) Max.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min. [10 ms] (Nominal coil voltage applied the coil, excluding contact bounce time.
(1,000 Vrms for 1min: Form high sensitivity type) (Detection current: 10mA.197 .)
Release time [Reset time] (at 200C 680F)
Max.11 Approx. switching voltage 220 DC, 250 VAC
Max.3 (Detection time: 10|as. .)
(without diode)
Mechanical
characteristics
Shock resistance
Functional”2 Min. (Byvoltage drop 1A)
Contact material Ag+Au clad
Rating
Nominal switching capacity (resistive load)
Max. level])
2* Half-wave pulse sine wave: 11ms; detection time: 10|as
3* Refer “6. [10 ms] (Nominal coil voltage applied tothe coil, excluding contact bounce time. 980 m/s2(Half-wave pulse sine wave: ms. perate and release tim characteristics
(2 Form single side stable type)
Test condition: Without diodeconnectedtocoil inparallel
5-(1). carrying current A
Min. Specifications
Characteristics Item Specifications
Contact
Arrangement Form Form C
Initial contact resistance, max.)
Between contact and coil
1,500 Vrms for 1min. 5x105rated load (at times/min.)
Vibration resistance
Functional 10to double amplitude 3.H. Max.)
Electrical Min. (TX/TX-S/TX-D relay AgPd contact types are available for low level load switching [10V DC, 10mA max