Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
5 (Detection time: |as)
Destructive
20 200 Hz, acceleration: m/s2{4. Application
EV Switch safety Switch for cut-off battery power supply
from system circuit, order protect human body from the
electric shock accidents the time maintenance, etc.H. (Detection current: mA, 50/60Hz)
Mechanical
characteristics
Lever operation force
<OFF ON> 10N 25N (Measurement position: center lever)
<ON OFF> (Measurement position: tip lever)
Interlock button operation force (when
canceling lock)
4N 1N
Shock resistance
(Switch: condition)
Functional
490 m/s2{50 G}
(Half-wave pulse sine wave: ms; detection time: |as, detections, time each)
Destructive 790 m/s2{80.5 G}
(Sweep time: minutes (log sweep), direction: hours each)
Expected life
Mechanical life Min. 100 (at 500 Megger)
Breakdown voltage (Initial, Between open
contacts, Between contacts and lever surface)
2,500 Vrms for min. (Not freezing and condensing low temperature)
Mass (Approx. 100 times (Switching with current-switching)
Electrical life
(Cut-off performance)
*No-load application
when ON. This switch
indicates contact welding doing (1) and (2), below.
ds 61213 151112D 161
Automotive
.
However, the switch can cut-off the power directly, even when
power not cut-off the system.
*1) the time OFF operation, the lever can change OFF
position without operation the interlock button.) 230 8.
* Usually display: “ON” “OFF”
Position lever during
contact welding
(2) The interlock button does not return.
*2) Please operate the lever after making the interlock button
slide down completely the side the cover.(AEVD)
RATING
Specifications
Characteristics Item
Specifications
80 type
Contact Contact arrangement Form A
Rating
Rated voltage 400 DC
Rated carrying current (Wire Bus bar size more than mm2)
Max.6 (Half-wave pulse sine wave: ms)
Vibration resistance
(Switch: condition)
Functional Acceleration: m/s2{4.
Position of
Lever-ON
(1)The Interlock Button slid down
to the cover side.
(2) The lever operated
[If contact welding occurs]
Contact welding may occur current switched contact
turning current that exceeds the specifications is
continuously applied when the power ON.16 (at A)
Insulation resistance (Initial, Between open
contacts, Between contacts and lever surface)
Min. not switch current contact turning ON.
* Please careful.
2.
Forward direction
(Polarity +)
5 times: 400 400 (Resistive load, Time constant: less than 1. this state the switch's contacts are not
OFF.03s (Wire Bus bar size more than mm2)
Electrical
characteristics
Contact voltage drop (Initial) Max.
(1) The lever will not all the way the OFF position when you
try turn off, and when you release the lever returns the
window that displays red.0 ms)
Conditions Conditions for operation, transport and storage
Ambient temperature: -40 +80°C -40 +176°F
Humidity: 85% R.
(1) The display window becomes “RED”.0 ms)
Reverse direction
(Polarity -)
5 times: -120 200 (Resistive load, Time constant: less than 1.
2) When turning the switch ON, the product designed to
prevent malfunction not allowing turn unless the
interlock button pressed when the lever operated. Please turn the lever the side and the
OFF side. carrying current 120 600s 5,560A 0. Please refer the
specification regarding the cut-off performance.11 oz
DESCRIPTION USAGE
1.
(2) The interlock button does not return. How use
1) When the switch turned and OFF, principle the
battery power already cut-off the system side (no current-
passing condition). 0
