Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
0 4.
9) When the screws for fixing relay-body and for additional
terminal are tightened, should used within the range of
decided torque.5 times more (at
least for rated type) the rated operation voltage.
3) includes ripple, the ripple factor should less than 5%.)
Varistor voltage: For input, Min.031inch and #250 tab terminal
5.
8) Take care avoid cross connections they may cause
malfunctions overheating.
13) the power turned off and then immediately after
applying the rated voltage (current) continuously the relay's
coil and contact, the resistance the coil will increase due a
rise the coil temperature. Usage, transport and storage conditions
1) Temperature: +80°C -40 +176°F (-40 +65°C -40
to +149°F when continually powered DC)
2) Humidity: 85% (Avoid freezing and condensation. Insertion strength into the tab terminal: Max.
6) the relay used while exceeding the coil rating, contact
rating cycle lifetime, this may result the risk overheating. Therefore, please
confirm with the actual load. When using zener diode (circuit)
ZD18V+
Diode voltage
f Clamp voltage
ZD30V Zener voltage
30V-12V=18V Clamp voltage
4) Lifetime specified under the standard test conditions JIS
C 5442. 49N (for
horizontal type)
Reference: Please select faston terminal (flat connection
terminal) which comply with JIS C2809-1999. (temperature 35°C 95°F, humidity 25%RH to
85%RH)
Lifetime dependent the coil driving circuit, load type,
operation frequency and ambient conditions.
5) Low temperature, low humidity environments
The plastic becomes brittle the relay exposed low
temperature, low humidity environment for long periods time. Cautions for Use
1) Regarding cautions for use and explanation technical
terms, please refer our general catalog.0 Nm,
Horizontal type (M4 screw): 2. Condensation will cause deterioration the relay
insulation.
158 ds_61213_en_ev_quiet: 010312D
.
5) When applying current which includes precipitous changes or
ripple, the relay may generate buzzing sound. When using varistor
Recommended Varistor; Maximum Energy: more than 1J
(However, please make settings using values that take
into consideration the worst case scenario. V
Ex.0 m
2) Tightening torque for contact terminal;
Vertical type (M5 screw): 3.
Especially, Contact terminals have polarity.8mm .2 2.8 m
3.)
The humidity range varies with the temperature. these circumstances, take measures
such reducing the load current, limiting the duration current
flow, and applying coil voltage higher than the rated operating
voltage (quick start)., that the clamp voltage reaches 1. Allowable pulling force for the coil input lead wire:
Max. Care must exercised when the relay be
used stored high ambient temperature.
2.
12) The relay contacts are encapsulated inert gas
atmosphere.
7) general rule, not use relay has been dropped. Please avoid such usage. the contact
terminals were connected with opposite pole, the electric life
would shorter. Check lifetime
under the actual condition. Use within the
range indicated the graph below.
11) the several relays are mounted closely heat-
generation object close the relay, take care check the
abnormal temperature-rise and the insulation distance between
the terminals outside the relay.10N (for vertical type)
4.
For coil surge absorption, please use zener diode varistor,
etc.
3) Atmospheric pressure: 106 kPa
Temperature and humidity range for usage, transport, and
storage
i Humidity, %RH
85-
I Tolerance range I
When continually
powered DC
/ /
/(Avoid freezing (Avoid /
/When used condensation ,
/temperatures when used at
flower than temperatures
/0°C 32°F) higher than
'//A 0°C 32°F) //
i i
-40
-40
0
+32
65 80
+149+176
Temperature, °F
4) Condensation
Condensation forms when there sudden change in
temperature under high temperature and high humidity
conditions.
Ex.
For plate thickness 0.
10) Avoid mounting the relay strong magnetic fields (near a
transformer magnet) close object that radiates heat. Condition tightening screw
1) Tightening torque for fixing relay-body;
Vertical and Horizontal type (M5 Screw): 3.(AEVS)
NOTES
1.
This causes the pick-up voltage rise, and possibly exceed the
rated pick-up voltage.
If only diode connected parallel with the relay coil, the
contact opening velocity will become slow and sufficient cutoff
performance cannot guaranteed.
2) Additionally the ambient temperature and condition for your
application should considered because pick-up and drop-out
voltage will changed.0 4
