Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
50ms
(Nominal coil voltage applied the coil, excluding contact bounce time)
Release time (at 200C 680F)
Max. switching capacity (resistive load) 12V DC*1
Max. Min.
ds_61213_en_ev_quiet: 010312D 155
Automotive
. Coil data
Type
Nominal coil
voltage
Pick-up voltage
(at 20oC 680F)
Drop-out voltage
(at 200C 68oF)
Nominal operating current
[+10%] (at 200C 68oF)
Nominal operating power
(at 200C 68oF)
Max. Specifications
Characteristics Item
Specifications
Vertical type Horizontal type
Contact arrangement Form A
Nominal switching capacity (resistive load) 60A 400V DC
Short term carrying current 100A min.H.H.This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual
load. (Not freezing and condensing low temperature)
Mass (Approx., 180A min. 0.6 m/s2{2 (Detection time: 10|as)
Destructive
10 100 Hz, acceleration: m/s2{4. (Not freezing and condensing low temperature)
Conditions for transport and storage
Ambient temperature: -40 +80°C -40 +176°F
Humidity: 85% R. cycles)*2,*3
Reverse direction shutoff -120A 200V (Min.At L/R 1ms
*4. cycles)*2,*3
Overload opening/closing rating 120A 400V (Min. 50ms
(Nominal coil voltage applied the coil, without diode)
Shock resistance
Functional
For ON: Min. (Detection current: 10mA)
Electrical
characteristics
(Initial) Between contact and coil 2,500Vrms/min. allowable voltage*1
60 Max. Refer “Usage ambient condition“ page 178. 0. 98m/s2{10 (Half-wave pulse sine wave: 11ms: detection time: 10|as)
Destructive Min.82 240 8. 196m/s2{20 (Half-wave pulse sine wave: 11ms: detection time: 10|as)
For OFF: Min. 800 cycles
Conditions
Conditions for operation
Ambient temperature: -40 +80°C -40 +176°F
(-40 +65°C -40 +149° when continually powered DC. (Detection current: 10mA) 2,000Vrms/min.The electrical performance value applies when varistor connected parallel the coil. 100MQ (at 500 DC, Measurement same location “Initial breakdown voltage” section.(AEVS)
RATING
1.375A 4.4 G}
100 200 Hz, acceleration: 19. (Detection current: 10mA)
Operate time (at 200C 68°F)
Max.
*2.47 oz
Notes:
*1. When continually powered, the maximum allowable voltage (at 65°C 149°F). 490 m/s2{50 (Half-wave pulse sine wave: 6ms)
Mechanical
characteristics
Vibration
resistance
Functional
10 100 Hz, acceleration: m/s2{4. shutoff current 600A 300V (Min.) 250 8.5 DC
Note: *1.4 G}
100 200 Hz, acceleration: 19.)
Humidity: 85% R. cycles)*2,*3
Contact voltage drop (Initial) Max. 2x105 (at cpm)
Electrical (resistive load) 60A 400V Min.)
Breakdown voltage Between open contacts 2,500Vrms/min.
2. (Detection current: 10mA) 2,000Vrms/min.6 m/s2{2 G}
(Time vibration for each direction: direction: hours)
Expected life
Mechanical Min. (15mm2Wire)
Contact rating
Min. Please warned that working life will reduced when diode used.067 (By voltage drop 20A)
Insulation resistance (Initial) Min.
*3
