Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Poznámky redaktora
85°C 181 ),
Humidity: 85% R. 105 Min. cycle)*2,5
2,500A 300V DC
(Min. 3,000*2
80A 400V DC
Min. m/s2
{4. (Not freezing
and condensing low temperature)
Mass (Approx. 1,000*2
30A 400V DC
Min.1V
(200 Carry
current)
Max. (Detection current: 10mA)
Between
contact and coil
2,500Vrms/min. L/R 1ms
*6.46 oz
Notes:
*1. switching capacity
(resistive load)*1
1A 12V DC*1 12V DC*1 12V DC*1 12V DC*1 12V DC*1 24V DC*1
Max. 50
cycles)*2,5
—
600A 400V DC
(Min. 30ms
(Nominal coil
voltage applied to
the coil, excluding
contact bounce
time. 1,000
cycles)*2,5
-300A 200V DC
(Min. 196m/s2{20
G} (Half-wave
pulse sine
wave: 11ms;
detection time:
10|as)
For ON: Min.11 600 21. Specifications
Characteristics Item
Specifications
10A type 20A type 80A type 120 type 200 type 300 type
Contact rating
Contact arrangement Form A
Nominal switching capacity
(resistive load)
10A 400V 20A 400V 80A 400V DC
120A 400V DC
(Carry current)
200A 400V 300A 400V DC
Short term current
15A 2min,
30A 30sec
(2mm2)
40A 10min,
60A 1min (3mm2)
120A 15min,
180A 2min
(15mm2)
225A 3min,
400A 30sec. (Detection current: 10mA)
Operate time (at 200C 68°F)
Max. Refer “Usage ambient condition“ page 178.)
Max.03V
(By voltage drop
6 20A)
Max.(AEV)
2. 490 m/s2{50 (Half-wave pulse sine wave: 6ms)
Vibration
resistance
Functional 200 Hz, Min.17 180 6.11 400 14. 75,000*2
20A 400V DC
Min.5 (Detection
time: 10|as)
Destructive
10 200 Hz, Min. 2x105
Electrical (resistive load)
10A 400V DC
Min. 100MQ (at 500 DC, Measurement same location “Initial breakdown voltage” section.43 m/s2{4.
*3. Condition: Nominal switching cycles, each cut-off 2,500 A
*4. The coil voltage type and type have the same specifications. 0.
*2.5 (Time of
vibration for each
direction; Z
direction: hours)
Expected life
Mechanical Min. 50
cycles)*2,5
-120A 200V DC
(Min. (Not freezing and condensing low temperature)
Ambient temperature:
-40 +850C -40 +1850F
(Storage: Max. 196m/s2{20 (Half-wave pulse sine wave: 11ms; detection time: 10|as)
For OFF: Min. m/s2
{4.35 400 14. cycle)*2,5
1,200A 300V DC
(Min. cycle)*2,5
2,000A 350V DC
(Min. The electrical load performance value for the 10A, 20A, 80A, 120A and 200A types applies when varistor connected parallel the coil. 50ms
(Nominal coil voltage applied the coil, excluding contact bounce time.43 m/s2{4. 98m/s2{10 (Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min.06V
(300 Carry
current)
Electrical
characteristics
Insulation resistance (Initial) Min.H.
(38mm2)
300A 15min,
(60mm2)
400A 10min,
600A 1min. 10ms
(Nominal coil
voltage applied to
the coil, without
diode. Please warned that
working life will reduced when diode used.)
Max. cycles)*2,5
120A 400V DC
(Min.16 750 26.)
Breakdown
voltage
(Initial)
Between open
contacts
2,500Vrms/min. 50
cycles)*2,5
800A 300V DC
(Min. cycles)*3,5
Overload opening/closing
rating*5
30A 400V DC
(Min. 3,000*2
300A 400V DC
Min. 0.4 G}
(Time vibration for each direction; direction: hours)
10 200 Hz,
Min. 50
cycles)*2,5
60A 400V DC
(Min. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. 300 cycles)
Reverse direction cut-off*5 —
-120A 200V DC
(Min. 50
cycles)*2,5
120A 400V DC
(Min. 1,000
Conditions
Conditions for operation,
transport and storage
Ambient temperature:
-40 +800C +176°F (Storage: Max. 50
cycles)*2,5
-200A 200V DC
(Min.)
Release time (at 200C 680F)
Max.H.)
Mechanical
characteristics
Shock
resistance
Functional
Min.85oC 1850F),
Humidity: 85% R.4 (Detection time: 10|as)
10 200 Hz,
Min. 3,000*2
200A 400V DC
Min. 0.
(100mm2)
Min. cut-off current*5 —
800A 300V DC
(Min. 0. 100 cycles)
Contact voltage drop (Initial)
Max.2V
(By voltage drop
6 20A)
Max.
ds 61213 ev: 151112D 147
Automotive
.
*5. 0. 0.067V
(By voltage drop
6 20A)
Max. 30ms
(Nominal coil voltage applied the coil, without diode.5V
(By voltage drop
6 10A)
Max.) 3
