Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
C.8W
N.5G}
Destructive 2,000 Hz, Min.: 10A
1.C.C.H.: 10A 28V DC
N.4W 1.5G} Time vibration for each direction; direction: hours
Expected life
Electrical (at nominal switching capacity) Flux-resistant type: Min.: 40A 14V DC
N. 44.: 30A 14V DC
45A
14V DC
50A
14V DC
25A 28V DC
N.H.1m/s2{4.4W (PC board type)
Note: All other specifications are the same those standard type (12 coil voltage)
3) Heat resistant type (12 and coil voltage)
Characteristics Item
Specifications
12V 24V
Contact
Arrangement Form Form C
High contact
capacity
(1 Form A)
1 Form Form C
High contact
capacity
(1 Form A)
Contact resistance (Initial) Max.: 20A, N.8W 1.: 10A 28V DC
20A 28V DC
Max.O.8W,
1.O.: 30A N.8W
1.8W, 1. Refer “Usage ambient condition“ on
page 178.: 30A 14V DC
40A 14V 20A 28V DC
N. The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value.C. 200 m/s2{20G}
Destructive Min.O.4W
(PC
board
type)
1.C.O.
*2.8W
20A 28V DC
20A
1. *Current value which carry current possible when the coil temperature 180°C 356°F
ds 61202 cb: 010113J 121
Automotive
.4W 1. 44. 15ms (excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock resistance
Functional Min. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min. 15mQ (By voltage drop A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity
(Initial)
40A 14V DC
N.8W (1. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial) Min. (Detection current: 10mA)
Operate time (at nominal coil voltage)
(at 20°C 68°F)
Max.
2) Standard type (24 coil voltage)
Characteristics Item Specifications
Contact
Arrangement Form Form C
High contact capacity
(1 Form A)
Contact resistance (Initial) Max. 5x104(Operating frequency: ON, OFF)
Mechanical Min.: 20A 28V DC
N.: 30A 14V DC
70A 14V (at 20°C 680F)
50A 14V (at 85°C 185°F)
Max.: 40A N. (Not freezing and condensing low temperature)
Heat resistant type; Ambient temperature: -40 +125°C -40 +257°F,
Humidity: 85% R.: 50A 14V DC
N. (Not freezing and condensing low temperature)
Max.CB
2. (at 500V DC, Measurement same location “Breakdown voltage” section. 15mQ (By voltage drop A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (Initial) 20A 28V DC
Max. 105, Sealed type: Min.: 40A 14V DC
N. 1,000 m/s2{100G}
Vibration
resistance
Functional 500 Hz, Min. carrying current (Initial)
(28V DC, 85°C 185°F, continuous)
20A
Nominal operating power 1.1m/s2{4. 15ms (excluding contact bounce time) (Initial)
Release time (at nominal coil voltage)
(at 20°C 68°F)
Max.4W 1.4W: board type)
Min.4W 1. 1.8W
1. operating speed cpm (at nominal switching capacity)
Mass Approx.O. 106(at 120 cpm)
Conditions
Conditions for operation, transport and
storage*2
Standard type; Ambient temperature: -40 +85°C +185°F,
Humidity: 85% R. carrying current (Initial)
(at 85°C 185°F, continuous)*
50A 14V DC
N.)
Breakdown
voltage (Initial)
Between open contacts 500 Vrms for min.: 10A 28V DC
25A 28V DC
Nominal operating power 1.O.: 25A 28V DC
N.: 40A, N.C. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load.16 oz
Notes:
*1.O.: 40A
Nominal operating power 1.C.O. Specifications
1) Standard type (12 coil voltage)
Characteristics Item Specification
Contact
Arrangement Form Form C
High contact capacity
(1 Form A)
Contact resistance (Initial) Typ2mQ (By voltage drop A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (Initial) 40A 14V DC
N.: 20A 28V DC
N.C.O.O.4W
(PC board type)
Notes: All other specifications are the same those standard type (12 coil voltage)
2. carrying current (Initial)
(14V DC, 85°C 185°F, continuous)
N
