Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
CA
2.)
Min. 100 m/s2{10G}
Screw-mounting and direct coupling type: Hz, Min.67 oz
31 1.H. 200 m/s2{20G}
(Half-wave pulse sine wave: 11ms;
detection time: 10|as)
Min.4 type)
30 12V (1.09 oz
Notes:
*1. (Detection current: 10mA)
Between contacts and coil 500 Vrms for min. 0.4 and 1.1 m/s2{4. 100 m/s2{10G}
(Half-wave pulse sine wave: 11ms; detection time: 10|as)
Destructive Min. Refer “Usage ambient condition“ on
page 178.8 W
Min.H.3 V
[by voltage drop
12 (1. 0. 100 m/s2{10G}
Screw-mounting and direct coupling type: Hz, Min.5G} (Detection time: 10|as)
Destructive
Rubber bracket type: 500 Hz, Min. 0. switching capacity (resistive load)*1 14V DC
Electrical
characteristics
Insulation resistance (Initial)
Min.1 m/s2{4.
114 61201 ca: 010113J
. 106(at 120 cpm) Min.4 W/1. 105(operating frequency: ON,
2s OFF) (1. 10ms (at nominal voltage) (excluding contact bounce time) (Initial)
Mechanical
characteristics
Shock
resistance
Functional
Min. Specifications
1) type
Characteristics Item
Specifications
1 Form type Form type Form type
Contact
Arrangement Form Form Form C
Contact resistance (Initial) Typ 3mQ (By voltage drop 1A)
Contact voltage drop (after electrical life test)
Max. 104(operating frequency: 3s
ON, 15s OFF) (1. (at 500V DC,
Measurement same
location “Breakdown
voltage” section.8 type)
20 continuous continuous
Nominal operating power 1. MQ
(at 500V DC, Measurement same location as
“Breakdown voltage” section.)
Breakdown
voltage (Initial)
Between open contacts 500 Vrms for min.8 1. 85% R.
*2.5G},
Time vibration for each direction; direction: hours, direction: hours
Expected life
Electrical (at nominal switching capacity)
Min.81 oz,
Screw-mounting and direct coupling type: . (1.8 type)
20 DC
Max. 105(operating frequency: ON, OFF)
Mechanical Min.4 type)
30 for min.4 V
(by voltage drop
12 A)
Contact material alloy (Cadmium free)
Rating
Nominal switching capacity (resistive load)
20 12V (1. 1,000 m/s2{100G} (Half-wave pulse sine wave: 6ms)
Vibration
resistance
Functional
Rubber bracket type: 500 Hz, Min. 10ms (at nominal voltage) (excluding contact bounce time) (Initial)
Release time (at 20oC 68oF) Max.8 type A)
Min.4 type),
12 (1. The upper operation ambient temperature limit the maximum temperature that can satisfy the coil temperature rise value. (Not freezing and condensing low temperature)
Max. carrying current
(at coil applied voltage DC, 800C 176°F)
20 continuous (1. This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended check this with the actual load. 105(at 120 cpm)
Conditions
Conditions for operation, transport and
storage*2
Ambient temperature: -300C +800C 220F +1760F,
Humidity: R. 44. (Detection current: 10mA)
Operate time (at 20oC 68°F) Max.8 type)]
Max.8 type A)
Min.8 type: A)
15 cpm (at nominal switching capacity)
Water-proof
standard
Water-proof standard Sealed type: JIS 0203 S2, Dust cover type: JIS 0203 R2
Mass
Rubber bracket type: . operating speed
15 cpm (1.4 type: nominal load,
1. 44.3 V
(by voltage drop
12 A)
Max