Apply current for sec. Behaviour external push button/IR “Light“
12 Light ON/OFF activated
Light ON:
Push button pressed briefly: Light OFF Active after sec. Range Coverage
PD4-M-1C
In case the sensing area the LUXOMAT®
PD4-M-1C too large areas are being covered
that should not monitored, the range can be
reduced limited through use the enclosed mask-
ing clips.
Push button held down: Light OFF Active after sec. Behaviour external push button/IR “Light“
Activation light for via mains interruption
1., then forced shutdown the set brightness still exceeded., the
light switched permanently. See also Remote control–> Eye section
3. Switch for min.
3.
If the eye push button pressed, the switch-off threshold is
recalculated.
Other functions
15. Technical data PD4-Master-1C
1. When the 230 removed, the
light switched off and automatic mode activated.
HA
ON/OFF
16. Interrupt current
2. Apply current
5.
Switch-off takes place automatically manuelly.
230 for sec.The “Corridor“ and “Light ON/OFF“ functions are mutually
exclusive. Apply current
5. both are activated, the detector performs the corridor
function.
Declaration Conformity: The product complies
with the low voltage recommendation 2006/95/EC
and the EMV recommendation 2004/108/EC. Internal calculation the switch-off value
2. 30min. 16min. Accessory
Sensor and power supply one case
Power supply: 230 ±10 %
Power consumption: 1W
Ambient temperature: -25°C +50°C
Degree protection/class: IP20 II
Settings:
Potentiometer, DIP-switch and remote
control
Light values:
20 1000 Lux (with remote control)
10 2000 Lux (with potentiometer)
Extension the detection area: with Slave-devices
Area coverage: circular 360°
Range coverage 2,50 18°C:
seated 6,40 tangential radial m
Recommended height for mounting: m
Light measurement:
mixed light, daylight +
artificial light
• Channel for light control
Type contact: NOC/with pretravel tungsten contact
Contact load: 2300 cos ϕ=1 /
1150 cosϕ= 0. Exclude sources interferences
Typ FM
PD4-M-1C (Master) 92580 92585 92575
PD4-S (Slave) 92142 92254 92163
LUXOMAT®
Remote control:
IR-PD (incl. Detector simple closed state
230 permanently the slave input
If 230 applied the slave input for longer than sec. Interrupt current again
4./ test with potentiometer
5min.
If the switch-on threshold has been modified the potentiometer
or remote control, the switch-off threshold stored the EEPROM is
deleted and then recalculated the next activation.
13c.
Determining the switch-off value
1. with dark and motion
2.
- Channel switches the event motion “dark“ is
detected.
Behaviour external push button/IR
„Forced shutdown“
walking towards
walking across
seated
1
2
3
24 m
8 m
6,40 m
2
4
m
360°
2,50 m
2
3
1
20. However, the difference that switching-on
must always carried out manually!
As many (closer-contact) buttons desired can wired in
parallel the “S” button input (ON/OFF).
Switch-off threshold brightness
Forced shutdown active
Light OFF:
Light OFF: Push button pressed briefly: Light for approx.
This compensates for any brief fluctuations the brightness.
30 min.
Semi automatic operation
In this operating condition, order gain increased
savings, the lighting energized only after being manually
switched on.
Push button held down: OFF
Light OFF:
Push button pressed briefly: Light long motion Lag time
Push button held down: ON
12 Light ON/OFF deactivated
Light ON:
Push button pressed briefly: Light OFF long motion Lag time
Push button held down: Light OFF long motion Lag time
Light OFF:
Push button pressed briefly: Light long motion Lag time
Push button held down: Light long motion Lag time
13b.
Light OFF:
Push button pressed briefly: Light long motion Lag time
Push button held down: Light long motion Lag time
13a. wall bracket) 92160
Accessory:
BSK Ball basket guard 92199
Wall bracket for remote control as
replacement 92100
18.
17. Apply current for sec.
The behaviour when the push button pressed defined
as follows:
Corridor function activated
Light ON:
Push button pressed briefly: Light OFF Active after sec. minutes.
The semi automatic mode basically behaves like the fully
automatic one. push button connection S
If 230 applied for sec. motion (despite semi
automatic mode).
3.
14. push button connection S,
this interpreted slave signal slave connection This ensu-
res that the detector compatible with previous versions.
12./ test with remote control
Dimension [mm]:
PD4-M-1C FM
65 97
Visible portion when built into ceiling FC: mm
Technical data PD4-Slave
Electrical data same above, but just one channel
for signaling motion detection. Interrupt current again
4.
Fully automatic and semi automatic mode
(see functions IR-PD-M-1C)
Fully automatic operation
In this operating mode, the lighting switches automatically
on and off for increased comfort, depending presence
and brightness.
Triggering semi automatic mode: the detector switches
off semi automatic mode (lag timer elapsed), the detector
is switched again within sec. Light OFF for sec.
19. Article Part nr. Detector now for h
Exiting sabotage
1.5, µ-Contact
Time-settings:
5sec.
Switch-off delay
If the determined switch-off threshold exceeded during operation,
the detector only switches off after delay approx. Interrupt current
2. Wiring diagram
Standard mode with master 1-channel occupancy
detectors (N/O) with and terminal
SM
FC
FM
Optional
T1 NO-button for semi automatic mode;
Extension the detection area with Slave-devices
.
3
