Návody k různým produktům Enika Nová Paka ...
Poznámky redaktora
Finish measuring the time depressing the push-button the
receiver
Erasing the transm itter:
a) all the transmitters
1. repeated depressing the push-button the receiver, select
“erase all”, and keep the push-button depressed for more than s
2. prepare the selected transmitter
E ntry the transm itter into the ory the receiver:
Principle the entry:
• repeated short depressing the push-button the receiver
(less than selection the operation from the main offer or
function
• long depressing the push-button the receiver (more than s)
= confirmation the operation from the main offer function
• any following depressing must effected within s
- after the elapse the receiver brought back its initial
state repeat the entry procedure. Depress twice (more than the respective push-button the
selected transm itter which you intend erase
Simultaneous flickering the LEDs “channel and “channel B”
confirms the erasing the respective transmitter (the other ones
remain the memory)
PUSH-BUTTON THE RECEIVER MAIN OFFER
— PROGRAMMING STEPS
1.r. Simultaneous flickering the LEDs “channel A", “channel B”
confirms that the entry correct
Note: Proceed this way when entering thefunctions ”,
“OFF”, “ON/OFF”, “PUSH BUTTON”
Entry the function “timer”.cz )
Tx Tango
L sig allin alight flickering
During the entry:
Channel B
Channel I
code entered already
During the operation:
| BATTERY
replace the battery the transmitter
that has transmitted last time
• SIGNAL reception signals from the transmitter,
eventually interference
W !:
With the execution Rx2 (floating code), the function “push
button” cannot employed!
The receiver cannot employed safety STP push-button. repeated short depressing the push-button the receiver,
select the function “timer” determ ined the combination of
the three upper LEDs (see printing the receiver)
4. Within confirm long depression the push-button of
the receiver
3. repeated depressing the push-button the receiver, select
“erase one code”
2. remove the cover
2. SELECT FUNCTION s
4. repeated short depressing the push-button the receiver,
select its function this determ ined the combination the
three upper LEDs! (see printing the receiver)
4.
In case defect, return the manufacturer Enika s. Within confirm long depression the push-button of
the receiver
5. Within confirm long depression the push-button of
the receiver
3.o. m
O0^0
o
0
O O0
0 O
<2 SELECT
>2 CONFIRM
>10 SERASE ALL*
>4 ERASE SET
t F4/1500 A
0 0
I I
PROGRAMMABLE
FUNCTIONS
o
o
o
o
o
o
o
BATTERY
ERASE
ERASE
ONE CODE
MEMORY
CHANNELB
CHANNEL A
¡IGNAL
o 6~à 6~~ô
Z N
| J
\4-------24 V~= ►)
ON After depressing the transmitter, the relay is
operated always, and remains operated
irrespective its prior condition
OFF After depressing the transmitter, the relay is
released always, and remains released
irrespective its prior condition
TIMER After depressing the transmitter, the relay is
operated for pre-set time min. Simultaneous blinking the LEDs “channel and “channel B”
confirms the erasing all the transmitters
b) one transmitter
1. Within confirm long depression the push-button of
the receiver
3.
Bringing into operation:
1.
1. CONFIRM CHANNEL 8
3. The receiver will behave shown in
the figure
Survey transm itters control
o receiv actual list on
www. repeated short depressing the push-button the receiver,
select “memory" into the respective channel (channel channel B,
channel B)
2.) signalled simultaneous flickering the
LEDs “channel and “channel B”
6.x2, x2-12, x2H two-channel receiver “short” depressing less than “long” depressing ore than unction the receiver:
Description:
The receiver can employed for the control two appliances of
your own choice means the transmitters the BOSYs line.
<gz
Technical data: Rx2, Rx2-12, Rx2 H
N ber controlled channels:
M ax. 1,5 2
For Rx2-12 only
FUNCTION LED
12. Depress twice (more than the respective push-button the
selected transmitter
6. CONFIRM FUNCTION 8
5.IL tr
111
ta.
The connection the receiver the mains (or its disconnection
from the same) can effected workers acquainted with the
job least, compliance with the Decree 50/1978 L. s)
Fast entering does not apply to
Rx2H!:
1.TRANSMIT 2x
6. Within confirm long depression the push-button of
the receiver
5. Simultaneous flickering LEDs
“channel and “channel confirms
that the entry correct
4. Depress twice (more than the respective push-button the
selected transm itter, and start measuring the time with watch
(l min.)
ON/OFF After depressing the transmitter, the relay is
switched the contrary position
PUSH BUTTON After depressing the transmitter, the relay is
operated, and remains operated
whilst the push-button the transmitter is
held depressed (max.
E ntry procedure: (for push-button transmitters only)
1. repeated short depressing the push-button the receiver
select “memory” into the respective channel (channel channel B,
channel B)
2. connect the supply voltage
3.,
Nádražní 809, 509 Nová Paka. ENDTIMER SETTING
(TIMER ONLY) 8
Q
z
si u.enika. SELECT CHANNEL <2s
2. Within depress all the push
buttons the selected transm itter
3. actuated output:
2
■ 750 VA
2 350 VA
Supply: 230 V/50 Hz, VAC/DC (12 DC)
Operating frequency: 433,92 Hz
Protection contact relays: 4/1500 250 V
Protection: IP20
Operating temperature: -10 55°C
N ber codes/combinations: 224 2s2 (H)
M axim number codes the memory: 21,6 (H)
Connecting clamps: max. Depress the push-button the re
ceiver and keep depressed until the
LED “memory” gets alight
2.G
