remove the cover
2. confirm within means long press the receiver
button
3. select «erase all» repeatedly pressing the button and then hold
the button for longer than 10s
2. the simultaneous flashing the «close» and «open» LEDs
confirms the correctness the entry and the opening the roller
shutters thus ensues signalled the «open» LED
7.5 2
□
▲
UP/DOWN
E T
T R
•p ressin tra itte r’s upper tto e
ro ller shutter opens its fin sitio n
H
•p ressin tra itte r’s lower tto e
ro ller shutter closes its final osition
NEXT Tx
E R
T S
T tro sam for N
fu ction
H▲
POSITION
E D
P N
•p ressin tra itte r’s upper tto e
ro ller tter opens red efin sitio n
b
•p ressin tra itte r’s lower tto e
ro ller tter closes red efin sitio n
CENTRAL
E F
S A
S /
D Y
B D
(th tim rem ain sam for e
U ctio )
&▲
•p ressin tra itte r’s upper tto e
ro ller tters open ith tio f
sto )
•p ressin tra itte r’s lower tto e
ro ller tters close ith tio f
sto )
LED signalling: alight flickering
During the entry:
CLOSE code entered already
OPEN y
During the operation:
replace the battery the transmitter
BATTERY
that has transmitted last time
SIGNAL reception signals from the transmitter,
eventually interference
WARNING!:
• This receiver only enables two-button control. codes the mem ory: 20
connecting term inals: ax. confirm with long press the button within s
5.
Tx Pocket4 Element
. has been adapted for assembly the
installation box.G. select «memory» and «close» means repeated short presses
on the receiver button
2.
Bringing into operation:
1. the simultaneous flashing the «close» and «open» LEDs
confirms the deletion all the transmitters
b) single transmitter
1.Roll Function the receiver:
Description:
The receiver can used control window roller shutters using a
BOSys series transmitter.,
Nádražní 809, 509 Nová Paka. select «memory» means repeated short presses the
receiver button
2.cz )
Tx Key Tango
^E 3
Technical data: Roii
pow source: 230V /50 Hz
operating frequence: 433. prepare the selected transmitter
The entry principle:
• the repeated short pressing the button the receiver (less
than the selection the operation from the main menu or
function
• long press the button the receiver (more than s)
= confirmation the operation from the main menu function
• any further pressing the button must occur within s
Setting the default position for the roller shutter position:
1. 1. no. select «erase one code» repeatedly pressing the button
2. press the receiver button once the roller shutters have reached
their final position
The entry procedure for the «POSITIO function
1-6 see the previous paragraph
7. END TIMER SETTING
(TIMER ONLY) s
G SELECT
>2 CONFIRM
>10 ERASE ALL*
F4/1500 A
z
111
z
o
1=
(/)
s
0
O
0
I
IP/DOWN
0o
o
0
0
O
0
0
0
O
O
o
BATTERY
ERASE
ALL*
ERASE
ONE CODE
1 1
oMEMORY
FUNCTIONS
oCLOSE
oOPEN
B oSIGNAL
A1 B3
o 6
230 V-
24 V-
N N
S urvey transm itters for control the
receiver actual list www. select the «UP/DOWN» means repeated short presses of
the button this designated the com bination the three
upper LEDs! (see the printed area the receiver)
4.92 Hz
relay contact protection: F4/1500 250 V
shielding level: IP20
operating tem perature: °C
num ber codes/com binations:
224
m ax.TRANSMIT ^
4.
• The connection the receiver the mains (or its disconnection
from the same) can effected workers acquainted with the
job least, compliance with the Decree 50/1978 L.
• case defect, return the manufacturer Enika s. hold the button until the roller shutter completely closed
The entry procedure for the «UP/DOW function:
1.r. the simultaneous flashing the «open» and «close» LEDs con
firms the correctness the entry
Deleting the transm itter:
a) all transmitters
1. press twice (longer than the appropriate button(s) the
selected transm itter, which you wish erase
the simultaneous flashing the «close» and «open» LEDs
confirms the deletion all the appropriate transmitter (the others
remain the memory)
PUSH-BUTTON THE RECEIVER FUNCTION LED MAIN OFFER
— PROGRAMMING STEPS
1. press the upper button(s) from the selected transm itter twice
(longer than s)
6. after achieving the desired shutter position, press the receiver
button
The entry procedure for the «NEXT Tx» and «CENTRAL» func
tions
1-5 see the previous paragraph
6. CONFIRM CHANNEL s
3.o. confirm within with long press the receiver button
3. connect the supply voltage
3.enika. SELECT CHANNEL <2s
2
