The use of innovations and new technologies at Hageris always customer-driven. Every year, Hager evaluatesthousands of its customer contacts, resulting in detailedknowledge of its customers’needs in order to workefficiently and successfully.
with telephone cable
J-Y(ST)Y 0.14 mm2
-30 °C
IP66
10 units (in series)
2 extendable approx.
Various options are available for connecting the sensors (brightness sensor magnetic contact glass breakage sensor):
a) The sensor cable can routed easily from the flush-mounted wall box through the tunnel the RolloTec insert far the terminal block and securely
connected.T39
N2
1
L
2975
N2
1
L
2975
N L
2925
Sun protection function: with brightness sensor order no. MOhm
approx. Ohm
min. 1000 000 Lux, programmable
approx. 350 mW
2 metres
max.
The sun protection function only activated when the shutter has been moved to
its end position continuous run operation. with telephone cable
J-Y(ST)Y 0.
approx 000 Lux, fixed
approx. 0.
Lay sensor cable far from
230 cables possible. the glass broken, the
shutter automatically lowered, thereby protecting the property from the weather
and from unauthorised intrusion. 300 Lux, programmable
-30 °C
IP54
2 extendable approx.:
RolloTec glass breakage sensor
1pole NCC contact
max. the brightness
remains below the pre-set level for minutes, the shutter raised again. Rinse the sensor clean
water and affix the window glass.
L
N
N2
1
L
2975
N L
2925
N2
1
L
2975
N2
1
L
2975
L
2911
Ø mm
2 m
25 mm0169
27
84,5
61
25
0184
20 mm
0-20 mm19 mm
2 mm
Height mm
0170
RolloTec
.
LIYY 0.
c) For mounting, the sensor cable connector can plugged into the lower sensor connection.
b) The sensor cable can fed through the cable duct between the base plate and the flush-mounted wall box and fixed the terminal block.
Sensor connection options RolloTec inserts
a)
Connect wire marked
grey ground
Magnet/Glass
Ground
Brightness
b)
Connect wire marked
grey ground
Magnet/Glass
Ground
Brightness
c)
N L
2925
Terminal block Terminal block
Lay the sensor cable far from
230 cables possible.:
RolloTec brightness sensor
at approx.
0170
RolloTec glass breakage sensor
Mounted on
window pane
The glass breakage sensor can connected three different ways. balcony door shutters) (not with magnetic contact).
(See sensor connection options)
For attaching the window pane,
we recommend the glass metal
adhesive set made Loctite.6 mm, connect shield ground!
0169
Brightness sensor for suction attachment
RolloTec glass breakage sensor
The glass breakage sensor affixed the window pane. 5000 000 Lux, prog.
RolloTec inserts: operation several RCDs
Individual control Individual controlMaster control
Cut-off relay
MM
To avoid unwanted tripping the RCDs,
the circuits must decoupled. minutes before sunset
(see astronomical curve).5 sec.g. the pre-set Lux value exceeded, the
shutter lowered such that slits light still come through..
Twilight function:
The twilight function (only with timer) activated approx. number
Cable length
Order No. The shutter remains closed until command
is sent from the associated control mounting. 850 nm
approx., and affix the sensor the window pane with
special LOCTITE adhesive (see operating instructions)
Technical data
Contact
Switching capacity
Action radius
Contact resistance load
Alarm condition
Alarm duration
Connection cable
Temperature range
Index protection
Max.
Sensors must not connected in
parallel multiple RolloTec inserts. This connection can detached any time order prevent
unwanted lowering (e. attach, clean the glass with
meths similar, and the sensor with washing liquid.
External brightness sensor
Technical data
Maximum sensitivity diode
Sunlight brightness values
Comfort push-button with radio button sensor connection
Memory button with sensor connection
Timer with sensor connection
Twilight brightness values (only timer 1775. Master commands are not executed,
and brightness values are not processed. 0169
If the sunlight value (20 000 Lux programmable see technical data) exceeded
by minutes, the shutter automatically moves down until the sensor concealed;
then moves little until the sensor exposed once more.)
Temperature range
Index protection
Cable length
Order No.6 mm, connect shield ground.
The shutter lowered about minutes after the brightness has fallen below the
programmed level. Attachment: clean the surface the
glass with spirit methyl alcohol etc.
RolloTec brightness sensors
By connecting the RolloTec brightness sensors surface-mounted the RolloTec insert
the sun protection function can implemented
