It possible read and write without any contact means radio technology.
When connecting the RFID reader, first switch off the BENNING 750 Appliance
/ Tester! not remove insert the RFID reader during operation. Remove the RFID reader, reconnect it
and then switch the appliance tester. Confirm with
<Y es>. Wait until the orange LED goes out and acoustic signal emitted. from tra and search intern datab ase:
- Hold the scanning window the RFID reader over the RFID transponder and press the button
on the bottom the scanner.
- Confirm the queries.
For installation the tags, has observed that metallic surfaces strongly interfere with the
radio connection.56 MHz. Therefore, not install them directly onto metal metal housing.). RFID system
consists two components: transponder and reader.
- elect> ave and confirm the queries.:
009370
Interface:
USB 2. The reader reads data the tag and writes data the tag.1 FID ead Specification
B enning part no. not necessary to
In case faults, switch off the appliance tester. For
identification the object, the data can read out wireless technology via radio frequency
channel. The reader provided with a
USB 2. epeat
th process!
R ead ing no.2 eratin FID ead er
The RFID reader can used combination with the following device groups: BENNING 750 A
F read ing ritin sses, until ran out. If
a transponder has been identified, this confirmed acoustic signal.
- Make sure that the RFID lamp ("Power") switches on.
- The data are saved the RFID transponder.
- Hold the scanning window the RFID reader over the RFID transponder and press the button
on the bottom the scanner.
A rrect ritin cess ill sig lled ecu tive aco stic
sig als.
- Switch the BENNING 750 Appliance Tester ON. 165 110 mm
17.
- When the test result displayed, select ave >.
- Connect the RFID reader the BENNING 750 Appliance Tester (USB-A jack).
configurate the RFID reader.
17. The reader consists reader/writer unit with
antenna.56 MHz, see chapter "Optional Accessories"
R ead ing range:
typ. Always switch off the
device first!
08/ 2012 58
. The tag
stores data the tag and the connected object.
- Hold the scanning window the RFID reader over the RFID transponder and press the button
on the bottom the scanner.0 interface transmit the received data the BENNING 750 Appliance Tester.
- The writing process starts.
- The orange LED the RFID reader flashes.
- Message: "Do you want save the data record the RFID transponder?". Wait until the orange LED goes out and acoustic signal emitted.
A rrect ritin cess ill sig alled ecu tive stic sig als.BENNING BENNING 750 A
17.
- The orange LED the RFID reader flashes. mm, depending transponder
Typical read ing tim e:
100 ms
C rre consum ption:
typ. ead tio al)
RFID method for automatic and electronic identification objects per radio technology. 120 (active mode)
O eratin tem ratu re:
0 °C
S tem ratu re:
- °C
R elative hum idity:
20 %
P rotection category:
IP30
D ensions:
approx. The reading process started pressing button. The transponder (in the following referred
to "tag") the actual data carrier. Confirm with
<Y es>. Data ex
change between reader and transponder does not require direct contact (even not visual contact).
W ritin tran er: (in data)
- Create the inventory data test sample internal database select existing test
sample (ID no. marked object only sends its data, the reader calls the transponder.
A rrect ritin cess ill sig alled ecu tive stic sig als.
- The data are saved the RFID transponder.
Barcode labels can exchanged means RFID transponders.
- Message: "Do you want save the data record the RFID transponder?". process!
C issioning :
- Switch the BENNING 750 Appliance Tester OFF. epeat
th process!
W ritin tran er: red valu es)
- Carry out the test. (passive mode)
typ.
- The writing process starts.0 interface
O eratin voltage:
5V, supplied USB interface BENNING 750 A
S rted FID tran ers:
13. The device communicates with
passive transponders with 13
