ABB Vzduchové jističe EMAX E1-E6 Montážní návody a manuály (03)

| Kategorie: Návody k obsluze Montážní návody  | Tento dokument chci!

Vydal: ABB s.r.o, ELSYNN Autor: ABB ELSYnn

Strana 194 z 660

Vámi hledaný text obsahuje tato stránku dokumentu který není autorem určen k veřejnému šíření.







Poznámky redaktora
It also possible interrupt the password entry procedure pressing the ESC key. disconnected messages must appear; they do, do not close the circuit-breaker and make the correct connections. Input the password 8 Select "Install" and press "ENTER" 9.3. type circuit-breaker, Rating Plug size . No.3.3.1 Installation To complete the procedure for installing PR122/DC unit, follow the steps below: 1. With the circuit-breaker open and preferably isolated, install the protection unit the circuit-breaker 2. 12. If the password wrong, the message Wrong password appears and remains until the ESC key pressed (or until interval seconds has elapsed). positive result shown the circuit-breaker opening. Select "Circuit-breaker" 6 Select "Unit installation" 7.3 Initial settings If the PR122/DC supplied ready installed the circuit-breaker, ABB SACE set all the variables referring the circuit-breaker or the specific application correctly (e. Apart from this, absolutely indispensable for the user modify the password and carefully define each modifiable parameter, before putting the PR122/DC into service.3.3.1 connection test A If the PR122/DC was installed the user, important, before closing the CB, check the last line the display when the relay turned for the first time via PR030/B battery unit. Select the value the first figure between '0' and '9' means the and keys and press confirm the figure and then move enter the next one.3.5 Replacing electronic release 12. When the red led flashes and off and the message Installation (installation error) displayed, remove the PR030/B 10. The remove the connector, proceed indicated the figure alongside. The password valid for maximum two minutes from the last time key was pressed. therefore always possible to switch from "READ" "EDIT". It not strictly necessary complete the uninstalling procedure, but this enables the parameters relating the circuit-breaker, such contact wear and others, otherwise these data would lost. For the PR120/V-PR120/LV module, set the Rated Voltage suitably. Select "Unit installation" 5.3 Putting into service 12. 12..3.4 Password management Specify password? [0***] To enter "EDIT" mode necessary enter four-figure numerical password. 12.2 Uninstalling To complete the procedure for uninstalling PR122/DC unit, follow the steps below: 1. Then test can conducted the whole chain, again using the specific function (Trip test). After entering the fourth figure, check the password you have entered.4. For the default password see par. Model L3447 pparatus Emax cale Doc. 12. By setting the value the password [0000] (on the "Unit configuration" menu) the password prom disabled. the password correct, you from the "READ" state the "EDIT" state.To run Trip Test, press the Test” button and the Enter” button simultaneously.g. 36/1 08 T 1/6 C s A t T rip ) C open .4. Check the open closed state the circuit-breaker the same "PR122/DC Test" screen, checking that closed and de-energized. Select "Circuit-breaker" 4.4). Remove the PR030/B module 8 Remove the PR122/DC unit from the circuit-breaker 9. Check for the absence configuration errors.5.12. Input the password 6 Select "Uninstall" and press "ENTER" 7. Enter the unit's "Settings" menu 5..5. With the circuit-breaker open and/or isolated power the unit from the PR030/B 2. 12. The data question are then transmitted the new PR122/DC unit installed the same circuit-breaker. 12. positive result shown the display.2 Test Before putting into service, test can conducted means the specific "Auto test" function which can activated the PR122/DC.). Enter the unit's "Settings" menu 3. Power the relay from any other source 11. Disabling the Password. 1SDH000635R0002 Page No. there are other errors, the display will show the message Configuration (configuration error) accompanied the yellow LED coming permanently (warning) 4. Power the unit ONLY from the PR030/B 3. Note that ABB SACE defines each possible setting according the content the paragraph the default parameters (see par.12.4. To enter new password, select the "New Password" item the "Settings/System" menu. The values attributable the password from 0000 9999