Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
5 DC
6.
3.
SPECIFICATIONS
Item Specifications
Breakdown voltage
Between input and output 2,000 Vrms for min.3 0. Refer the “REFERENCE DATA Load current vs. ambient temperature characteristics”.5 kgfcm}
Cross connection protecting diode 1.
Insulation resistance Min.)
Vibration resistance double amplitude .
R F
\ 2
2 2
0 ec
o 4
u e
V
d e)'(A
a
- 0
- 0
► F
- 0
- 0
A F
ds_61706_0001_en_rt3_powermos: 040413J 363
2
Power
. The load current varies depending ambient temperature.0 Min. 15.
2.0 DC
6. Equipped relay Maximum load voltage Recommended voltage Continuous load current Peak load currant
RT3SP1-12V AQZ102 V
0 (DC) (DC)
9 A
RT3SP1-24V (DC only) (DC) (100 shot)
RT3SP2-12V AQZ204 400 200 (DC) 0.3 1. 3. 9. Below 0°C 32°F, condensing water can freeze and cause socket contact failures and other problems.)
90% 110% rated input voltage
RT3SP1-24V
24 DC
Max.H.
RT3SP2-24V (6. This may cause some
troubles like insulation failure the socket the print circuit board. The input voltage can applied directly.
2.5 Min.0 typ.53 oz
Notes: The value breakdown voltage and insulation resistance the initial one.)
Note: This product has built-in input current limiting resistor; therefore, not necessary externally connect resistor the input. Take care under this condition.) (5.5 inverse voltage V
Unit weight Approx.
Rated input
voltage
Operate voltage
(at 25°C 77°F)
Release voltage
(at 25°C 77°F)
Input current (during application rated
input voltage) (at 25°C 77°F)
Allowable variation rated input voltage
(at -20°C +55°C -4°F +131°F)
RT3SP1-12V
12 DC
Max.
REFERENCE DATA
1 e
c )
Allowable ambient temperature:-20°C +55°C
-4°F +131°F
2 e
c )
Allowable ambient temperature:-20°C +55°C
-4°F +131°F
/
ß \
( p3).
2.
Between different terminals
(between relays, both ways)
1,500 Vrms for min.RT-3 Unit Relay/4-point Terminal (Power PhotoMOS Type)
RATING
1. (Not condensing)
Storage temperature -30°C +80°C -22°F +176°l (Not freezing and condensing)
Terminal screw fasten torque 0.) (6. Condensing occurs when the unit relay exposed sudden temperature change high temperature and high humidity atmosphere.039 inch
Shock resistance Min. Output ratings (per relay, 25°C 77°F)
Part No.7 typ. Take care under this condition.5 A
RT3SP2-24V (AC/DC dual use) (DC, peak value) 125 (AC) (DC, peak value) (100 shot)
Notes: During 4-point simultaneous operation, the rating per point also shown above. 100 (Using 500 megger, Measurement same location “Breakdown voltage” section.1 typ.2 typ.8 typ.5 typ. 100 3. Input ratings (per relay)
Part No. 196 m/s2
Ambient temperature -20°C +550C +1310F
Ambient humidity 35% 85% R. 3.
RT3SP2-12V (5
