Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
2V
(By voltage drop
6V 20A)
Max. (Not freezing and condensing low temperature)
Unit weight
Approx. 103*2
(Switching frequency:
6 times/min)
80A 400V DC
Min. 50ms
(Nominal voltage applied the coil, excluding contact bounce time)
Max. Note: diode used the life will lower. 10ms
(After the nominal
operation voltage
stops)
Mechanical
characteristics
Shock
resistance
Functional
10A, 20A (ON), 80A (ON), 200A (ON) and 300A (ON) types:
Min. 103*2
(Switching frequency:
20 times/min)
200A 400V DC
Min. 1,000 cycles)*2
-200A 200V DC
(Min. 196 m/s2(Half-wave pulse sine wave: ms; detection time: 10ps)
20A (OFF), 80A (OFF), 200A (OFF) and 300A (OFF) types:
Min. 0. 7. 100 cycles)*2
-80A 200V DC
(Min. 300 cycles)
Reverse cut-off rating
-20A 200V DC
(Min. 103*2
(Switching frequency:
6 times/min)
300A 400V DC
Min. m/s2(Half-wave pulse sine wave: ms; detection time: 10ps)
Destructive Min.H. cycles)*2
120A 400V DC
(Min. cycles)*2
-20A 200V DC
(Min. g
2. The upper limit the ambient temperature the maximum temperature that can satisfy the coil temperature rise value. Specifications
Characteristics Item
Specifications
10A type 20A type 80A type 200A type 300A type
Rating
Contact arrangement Form A
Nominal switching capacity
(Resistive load)
10A 400V 20A 400V 80A 400V 200A 400V 300A 400V DC
Max. cut-off current —
800A 300V DC
(1 cycle)*2
2,000A 350V DC
(1 cycle)*2
2,500A 300V DC
(3 cycles)*3
Overload cut-off rating
30A 400V DC
(Min. 600 g
21. 100 cycles)
Min. 0. +85°C +185°F),
Humidity: 85% R.820oz
Approx.5x104*2
(Switching frequency:
20 times/min)
20A 400V DC
Min.5V
(When carrying
current 10A)
Max.06V
(When carrying
current 300A)
Electrical
characteristics
Insulation resistance (Initial) Min.349oz
Approx.
Breakdown
voltage
(Initial)
Between open
contacts
2,500 Vrms for 1min.11oz
Approx. (Detection current: 10mA)
Between contact
and coil
2,500 Vrms for 1min.
348 ds_61C01_en_ep: 060313J
. contact allowance voltage 1,000V DC
Short term current
15A (3min)
(harness wire: 2mm2)
30A (30s)
(harness wire: 2mm2)
40A (10min)
(harness wire: 3mm2)
60A (1min)
(harness wire: 3mm2)
120A (15min)
(harness wire:
15mm2)
300A (15min)
(harness wire:
60mm2)
400A (10min)
(harness wire:
100mm2)
Max. 0.
Refer Usage, transport and storage conditions NOTES page 353. 3x103*2
(Switching frequency:
20 times/min)
60A 1,000V DC
Min. 1,000 cycles)*2
-300A 200V DC
(Min. 750 g
26.Please refer the reference data the following page for switching and cut-off 400 and higher. switching capacity 12V 12V 24V DC
Contact voltage drop (Initial)
Max. Condition: Switches rated number cycles each time there 2,500A cut-off.16oz
Approx.
*2. 0.1V
(When carrying
current 200A)
Max. 0.46oz
Notes:
*1. 180 g
6. 490 m/s2(Half-wave pulse sine wave: ms)
Vibration
resistance
Functional 200Hz, acceleration 43m/s2constant (Detection time: 10ps)
Destructive 200Hz, acceleration 43m/s2constant directions, each hours)
Expected life
Mechanical Min. Conditions: Varistor used for coil surge absorption. 100MQ (at 1,000V DC) Measurement same location “Breakdown voltage” section. cycles)*2
60A 400V DC
(Min. 3x103*2
10A 1,000V DC
Min. 400 g
14.EP
2. cycles)*2 —
600A 400V DC
(Min. 30ms
(Nominal voltage
applied the coil,
excluding contact
bounce time)
Release time (at 20oC 68oF)
Max. 30ms
(After the nominal operation voltage stops, without diode)
Max. (Detection current: 10mA)
Operate time (at 20oC 68°F)
Max. 2x105
Electrical*4
(Resistive load)
10A 400V DC
Min.
*3.
*4. 103
(Switching frequency:
6 times/min)
Conditions
Conditions for operation,
transport and storage*1
Ambient temperature: -40°C +80°C -40°F +176°F (Storage: Max. 105 Min.067V
(By voltage drop
6V 20A)
Max
