|
Kategorie: Katalog |
Tento dokument chci!
Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
Strana 312 z 1090
«
Vámi hledaný text obsahuje tato stránku dokumentu který není autorem určen k veřejnému šíření.
»
Jak získat tento dokument?
Poznámky redaktora
110 61022 txs: 060213D
. 750 m/s2(Half-wave pulse sine wave: ms; detection time: 10|as.)
*2 Refer “6. Usage, Storage and Transport Conditions” inAMBIeNt ENVIRONMENT (page 626). Specifications
Characteristics Item Specifications
Contact
Arrangement Form C
Initial contact resistance, max.TX-S
3) coil latching (L2, LT)
Nominal coil
voltage
Set voltage
(at 200C 68°F)
Reset voltage
(at 200C68OF)
Nominal operating
current
[±10%] (at 20°C 68°F)
Coil resistance
[±10%] (at 20°C 68°F)
Nominal operating
power Max.5V DC
80%V less of
nominal voltage*
(Initial)
80%V less of
nominal voltage*
(Initial)
46. switching current 1A
Min. level]. switching voltage 110V DC
Max. .) (without diode)
Mechanical
characteristics
Shock resistance
Functional Min.6mA 289Q 289Q
6V 11. 5x107(at 180times/min.3mA 129Q 129Q
4. ms] (Nominal coil voltage applied the coil, excluding contact bounce
time.3mA 3,840Q 3,840Q 150mW 150mW
*Pulse drive (JIS 5442-1986)
2.8mA 5.8mA 1,157Q 1,157Q
12V 5.7mA 46.5V 15.8mA 2,057Q 2,057Q
24V 6.071 oz
*1 This value can change due the switching frequency, environmental conditions, and desired reliability level, therefore recommended checkthis with the actual
load.7mA 32. Max. ms] (Nominal coil voltage applied the coil, excluding contact bounce
time.3mA 23. (Detection current: 10mA)
Between contact and coil 1,800 Vrms for 1min. [Max.)
Vibration resistance
Functional 10to double amplitude 3. 1,000MQ (at 500V DC)
Measurement same location “Initial breakdown voltage” section.)
Electrical Min. operating speed (at rated load) times/min.
Unit weight Approx. (Not freezing and condensing lowtemperature)
Max.3 (Detection time: 10|as. (AgPd contact type available for low level load switching [10V DC, 10mA max. [Max.7mA 514Q 514Q
9V 7. switching capacity (Reference value)”1 10pA 10mV DC
Nominal operating
power
Single side stable mW(1.)
Release time [Reset time] (at 20°C 68°F) Max.7mA 11.6mA 15.1Q 32.8mA 7.5to 12V DC), mW(24 DC)
1coil latching mW(1.H.3mA 6.)
Destructive 10to double amplitude mm
Expected life
Mechanical Min.5to 12V DC), mW(24 DC)
2 coil latching mW(1. 2x105(1 30V resistive) (at times/min. (Detection current: 10mA)
Between contact sets 1,000 Vrms for 1min. switching power (DC) (resistive load)
Max. 100 (Byvoltage drop 1A)
Contact material Standard contact: Ag+Au clad, AgPd contact (low level load): AgPd+Au clad (stationary),
AgPd (movable)
Rating
Nominal switching capacity (resistive load)
Max. 50°C
(By resistive method, nominal coil voltage applied the coil; contact carrying current: 1A.)
Operate time [Set time] (at 20°C 68°F) Max. (Detection current: 10mA)
Surge breakdown
voltage (Initial)
Between open contacts 1,500 (10x160|as) (FCC Part 68)
Between contacts and coil 2,500 (2x10|as) (Telcordia)
Temperature rise (at 20°C 68°F) Max.)
Conditions
Conditions for operation, transport and storage”2
Ambient temperature: -40°C +70°C-40°F +158°F;
Humidity: 85% R.1Q
70mW 70mW 150%V of
nominal voltage
3V 23.
Breakdown voltage
(Initial)
Between open contacts 750Vrms for 1min. 1,000 m/s2(Half-wave pulse sine wave: ms.)
Destructive Min. applied voltage
(at 200C68OF)
Set coil Reset coil Set coil Reset coil Set coil Reset coil
1.5to 12V DC), 150 mW(24V DC)
Electrical
characteristics
Insulation resistance (Initial) Min
