Panasonic is part of a large worldwide groupselling relays and associated switching products under different brand names in different territories.The conditions of use in some territories may differ from those customary in Europe. In particular there are often major differences in regard to national and international specifications, such as UL, CSA, VDE, SEV, EVE, SEMKO, etc. Thus, when considering contact loads as stated in this catalogue (e.g. 10 A, 30 VDC for the SP relay) its hould be understood that these values are not necessarily an absolute maximum but tested ratings. Mostly the stated value has been tested for a certain life expectancy as stated by the manufacturer or the respective test house. Thus, under different conditions, the stated “maximum” may, in practice, be safely exceeded.
12) The relay contacts are encapsulated inert gas
atmosphere.
5) When applying current which includes precipitous changes
or ripple, the relay may generate buzzing sound.5 times or
more (at least for rated type) the rated operation
voltage.
6) the relay used while exceeding the coil rating, contact
rating cycle lifetime, this may result the risk of
overheating.Z. V
Ex.
15) the relay used for inductive load load) such that
L/R 1ms, add surge protection parallel with the inductive
load.îZD18V. this not done, the electrical life will decrease and
cut-off failure may occur.
20) not use this product such atmosphere where any kind
of organic solvent (as benzene, thinner and alcohol) and the
strong alkali (as ammonia and caustic soda) might be
adhered this product.en. Therefore,
please confirm with the actual load.
ds 61213 ev: 151112D 153
Automotive
.
(Ex.
ZD18V
D
ZD30V
For Cautions for Use, see Relay Technical Information (page 166). the wire diameter small, the maximum rated
contact current cannot guaranteed. When using varistor
Recommended Varistor; Maximum Energy: more than 1J
(However, please make settings using values that take into
consideration the worst case scenario.
If only diode connected parallel with the relay coil, the
contact opening velocity will become slow and sufficient
cutoff performance cannot guaranteed.
10) Avoid mounting the relay strong magnetic fields (near a
transformer magnet) close object that radiates
heat.g^î.
13) the power turned off and then immediately after
applying the rated voltage (current) continuously the
relay's coil and contact, the resistance the coil will
increase due rise the coil temperature.
The relay might have contact welding without such
countermeasure.
9) When the screws for fixing relay-body and for additional
terminal are tightened, should used within the range of
decided torque.
8) Take care avoid cross connections they may cause
malfunctions overheating. the contact
terminals were connected with opposite pole, the electric life
would shorter.yo'îa. Care must exercised when the relay be
used stored high ambient temperature. Please avoid
such usage.
19) The relay satisfies the protection level JIS 0203 (of
waterproof). Cautions for use
1) Regarding cautions for use and explanation technical
terms, please refer our “Relay Technical Information”. Check lifetime
under the actual condition.
22) not make additional manufacturing upon the relay
housing.
This causes the pick-up voltage rise, and possibly exceed
the rated pick-up voltage.
21) careful that foreign matter and oils and fats kind don't
stick the main terminal parts because likely cause
terminal parts give off unusual heat. (temperature 35°C 95°F, humidity
25%RH 85%RH)
Lifetime dependent the coil driving circuit, load type,
operation frequency and ambient conditions.vtOltage
ZD18V Zener Voltage
ZD30V Zener Voltage
^ 30V-12V=18V J
Clamp
voltage
777 777
ZD30V Zener Voltage
4) Lifetime specified under the standard test conditions JIS
C 5442.(AEV)
13.
Ex.
3) includes ripple, the ripple factor should less than 5%.
23) For shutoff these contact polarity, but confirm the
electric life using the actual load.
14) case using capacitive load (C-load), please take a
countermeasure pre-charging the capacitive load so
that the inrush current will not surpass 60A.) Carrying current; 60A: diameter 15mm2 more
17) Take care disconnect the power supply when wiring. Please take any countermeasures additionally if
it should installed the place where higher protection
level required., that the clamp voltage reaches 1. When using zener diode (circuit)
_ .)
Varistor voltage: For input, Min.er.
2) Additionally the ambient temperature and condition for your
application should considered because pick-up and drop
out voltage will changed.
18) not switch the contacts without any load the contact
resistance may become increased rapidly. these circumstances, take
measures such reducing the load current, limiting the
duration current flow, and applying coil voltage higher
than the rated operating voltage (quick start).
16) Use the suitable wire for wire the load side according to
the current.
7) general rule, not use relay has been dropped.
11) the several relays are mounted closely heat-
generation object close the relay, take care check the
abnormal temperature-rise and the insulation distance
between the terminals outside the relay.
For coil surge absorption, please use zener diode or
varistor, etc.
Especially, Contact terminals have polarity
